Engine-Codes.com
Engine-Codes – Nissan – P0335 Nissan

P0335 Nissan Code - Crankshaft Position Sensor Circuit

Quick Answer

The P0335 code for Nissan vehicles indicates a problem with the crankshaft position sensor circuit. Common causes include Faulty crankshaft position sensor, Damaged or corroded wiring connections, Issues with the sensor's reluctor ring. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

What it means
P0335 Nissan indicates Crankshaft Position Sensor Circuit.
Common causes
Common causes include Faulty crankshaft position sensor, Damaged or corroded wiring connections, Issues with the sensor's reluctor ring.
Severity
High - diagnose this code as soon as possible.
Can I drive?
Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
What is this?
Table of contents Created and updated by William Orellana on Aug 18, 2024
💬 Need more help? Ask Auto Expert for instant answers — it's free!
AutoCodes App

Fix Your Car Smarter

Try the New AutoCodes App!

Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.

AutoCodes App on Google Play

Code P0335 Nissan Description

The P0335 code for Nissan vehicles indicates a problem with the crankshaft position sensor circuit. The crankshaft position sensor is a vital component in the engine management system, as it helps the engine control unit (ECU) determine the position of the crankshaft. This information is crucial for the proper timing of fuel injection and ignition, ensuring optimal engine performance and efficiency. When the ECU detects a fault in the crankshaft position sensor circuit, it can lead to issues such as rough idling, stalling, poor fuel economy, and difficulty starting the engine.

OBDII Code P0335 Nissan - Crankshaft Position Sensor Circuit
P0335 Nissan Code - Crankshaft Position Sensor Circuit

Common Causes of P0335 Nissan

  1. Faulty crankshaft position sensor
  2. Damaged or corroded wiring connections
  3. Issues with the sensor's reluctor ring
  4. Electrical problems in the sensor circuit
  5. ECU malfunction

Symptoms of P0335 Nissan

  1. Engine misfires or hesitation
  2. Engine stalling or shutting off unexpectedly
  3. Difficulty starting the engine
  4. Reduced engine performance or power
  5. Illumination of the check engine light

How to Fix P0335 Nissan

  1. Diagnose the issue by using an OBD-II scanner to confirm the P0335 code and test the crankshaft position sensor's functionality.
  2. Inspect the sensor and its wiring for any visible damage or corrosion, and replace any faulty components.
  3. Test the sensor's output signal to ensure it is within the manufacturer's specifications.
  4. Clear the diagnostic trouble codes from the ECU and perform a test drive to verify that the issue has been resolved.
  5. If the problem persists, further troubleshooting may be required to identify other potential causes.

Cost to Fix P0335 Nissan

The cost of repairing the P0335 code for a Nissan vehicle can vary depending on several factors. Typically, replacing the crankshaft position sensor or repairing the sensor circuit can range from $100 to $300 for parts and labor. It's important to note that additional diagnostic time may be needed to pinpoint the exact cause of the issue, which can incur extra costs. As mentioned earlier, labor rates at auto repair shops can fluctuate, so it's advisable to obtain quotes from multiple sources to get an accurate estimate.

What does this mean?

Tech Notes for P0335 Nissan

Sometimes and in some models, low battery voltage or a weak starter can trigger a Crankshaft Position Sensor code. Before replacing any parts, recharge or replace the battery.

There is a service bulletin for the following Nissan models:

2004–2009 Nissan Titan
2004–2009 Nissan Armada
2004-2009 Nissan Titan, Armada Factory Service Bulletin OBDII Code P0335




User Submitted Video

When is the Code Detected?

The crankshaft position sensor (POS) signal is not detected by the Electronic Control Module (ECM) during the first few seconds of engine cranking

Need more information about the P0335 Nissan code?

Need more information on how to fix the P0335 Nissan code? Get Access to Factory Service Manuals

Need Help with the Code?

Get the P0335 Nissan code diagnosed by a professional: Find a repair shop in your area

Information for Specific Nissan Models

About the author: William Orellana is a Master Mechanic and Mechanical Engineer with over 30 years of experience diagnosing and repairing vehicles. Learn more about his background.

Frequently Asked Questions about P0335 Nissan Code

1. What are the common symptoms of OBDII code P0335 in a Nissan related to the crankshaft position sensor circuit?

- Common symptoms may include engine stalling, rough idling, difficulty starting the engine, and a decrease in fuel efficiency.

2. What are the possible causes of OBDII code P0335 in a Nissan?

- The code P0335 can be triggered by a faulty crankshaft position sensor, damaged sensor wiring, or issues with the sensor's connection to the vehicle's ECM.

3. How can I diagnose the cause of OBDII code P0335 in my Nissan?

- To diagnose the issue, you can use a scan tool to read the code, visually inspect the sensor and its wiring for damage, and perform electrical tests to check for proper sensor function.

4. Can I still drive my Nissan with OBDII code P0335 present?

- It is not recommended to drive your vehicle with code P0335 active, as it can lead to potential engine performance issues and further damage if left unresolved.

5. How difficult is it to replace the crankshaft position sensor in a Nissan to resolve code P0335?

- The difficulty of replacing the sensor can vary depending on the model of the Nissan, but it is generally considered a moderately challenging task that may require some mechanical expertise.

6. Are there any tips for repairing OBDII code P0335 in a Nissan at home?

- Before replacing the sensor, ensure that the wiring and connections are in good condition. It's also helpful to consult the vehicle's repair manual for specific instructions on sensor replacement.

7. Can a faulty crankshaft position sensor cause other issues besides triggering code P0335 in a Nissan?

- Yes, a faulty crankshaft position sensor can cause other issues such as misfiring, poor acceleration, and problems with the transmission shifting correctly.

8. How much does it typically cost to repair OBDII code P0335 in a Nissan at a dealership or auto repair shop?

- The cost of repairing code P0335 can vary depending on the extent of the issue and labor rates, but it generally ranges from $150 to $300 for parts and labor.

9. Will resetting the OBDII system clear code P0335 in a Nissan temporarily?

- Resetting the system may temporarily clear the code, but if the underlying issue with the crankshaft position sensor circuit is not addressed, the code is likely to return.

10. Is it possible for OBDII code P0335 in a Nissan to be a false alarm or intermittent issue?

- While intermittent issues can sometimes trigger the code falsely, it's essential to investigate the cause thoroughly to prevent potential engine problems in the future.

Discuss the causes and fixes for P0335 Nissan OBDII Code

Submit a New Comment

  • I have a check engine light ON and I cannot pass the smog with failure code P0335 on my nissan frontier 2000 truck. I mechanic told me they have to remove the intake manifold in order to access this sensor. The charge is a whopping $400

    Reply to Comment

  • Hello My Pathfiner is with this code P0336 and I have checked all component, is in the same way is there other possible case beside the instruction of this code

    Reply to Comment

  • What year is your Nissan Pathfinder? Please double check the code. There is no P0336 code for any Nissan Pathfinder or any Nissan vehicles.

    Reply to Comment

  • Can a PO335 CKP be repaired or will require a replacement?

    Reply to Comment

  • You need to replace the sensor, there are no instructions on how to repair it.

    Reply to Comment

  • 2004 Armada. The engine light is still on after the ecm relay has been replaced with codes p0420 and p430 (catalyst convertors) I'm being told my cats wouldn't cause the truck to continously stall when driving. Any suggestions? Mechanics are stumped. Cam shady sensor?

    Reply to Comment

  • It's possible but not very likely that the cats could make the engine stall. If you get the P0335 code, then you need to replace the crankshaft position sensor. The ECM relay could cause the engine to stall, but should not cause the P0335 code.

    Reply to Comment

  • Where is the place of this sensor in Nissan sunny 2010, I have changed the easy one(cam sensor) which is on the right hand, may I have an image showing this one, my car become better after I have changed the sensor.
    Thanks,,,

    Reply to Comment

  • Don't have the manual for the Sunny, but if is the same as the Nissan Sentra, then the sensor is on the back of the engine.

    Reply to Comment

  • P0335 Fixed on Nissan Altima:

    https://youtu.be/325s0pFQZtg

    Reply to Comment

  • what is the voltage spec on the orange wire at the crank sensor while cranking?

    Reply to Comment

  • What model and year is your Nissan?

    Reply to Comment

  • 2005 Nissan titan 5.6
    keep getting a p0335 customer was at Nissan dealer they installed a battery,crankshaft sensor and then told the customer that the computer was bad.....customer then took to a different repair shop to have a used pcm installed and flashed.....still same code...after clearing codes the check engine light comes right back on setting the code....im lab scoping the crank/cam signals and noticing the are at 8.45 volts while cranking the engine over. i think thats too low... i have checked the emc main relay and even by passed it ...still same voltage at the pcm on the sensor wires.... ohm check the wires/harness all within spec. checked voltage drop on the grounds all good 0.07 to 0.04 any ideas?

    Reply to Comment

  • found and fixed the problem...the camshaft sensor was pulling the line voltage down far enough while engine was cranking....causing the computer to think the crankshaft sensor was not working. replaced both crank/camshaft sensor with new Nissan parts.make sure to install the right sensor in the right location. both sensors are identical !!! tsb update to identify parts/numbers and location.

    Reply to Comment

  • Thank you for the information!

    Reply to Comment

  • Hey guys. 2005 nissan 350z bone stock. Put a double din head unit and two kenwood speakers in the rear and now getting a p0335 code. It doesnt even want to start. Any ideas. Used a matched wiring harness and everything to install head unit and grounded it using the large ground just behind the three dash gauges. Only weird wiring is to get the antenna to work right it was spliced to the power for the headunit. On the wiring harnesses it was a blue wire labeled power antenna with no matching wire for the pioneer fh-x720bt head unit harness. Radio reception was terrible till i powered it.
    Rly need help asap had to get towed home and about to pay a huge tow bill to get it dtowed to the garage.

    Reply to Comment

  • The code has noting to do with the audio system.

    It's possible the the audio system is draining the battery. If the battery is low, the engine will crank slow and the P0335 is trigger.

    You should start by removing the audio unit or jump the battery. Make sure you check all the fuses as well.

    Reply to Comment

  • 2003 350z...I just changed the clutch and flywheel and my car wouldn't start after, disconnected the ckp sensor and after a few cranks it started. So the following day bought a new ckp sensor after testing it with a volt meter to ensure it was good. Once installed my car still won't start and I am still getting a p0335 code and now it won't start with the sensor unplugged.

    Reply to Comment

  • Unfortunately the flywheel was not properly installed. You have to remove and install the flywheel again. The engine starts with the CKP sensor disconnected, because the ECM uses other sensor to read the engine position, but it will run in a fail-safe mode.

    Reply to Comment

  • We already checked the flywheel. There was only one spot for the dowel to go for the flywheel. If it was installed wrong I don't think the car would've ran smooth enough to be driven...I could be wrong but I know it's in right.
    Why won't it run without it connected now though is my question

    Reply to Comment

  • The ECM has stored some initial values for each sensor (factory stored values), if one of the sensor (e.g. CKP, MAF) is disconnected or gets damage (totally damage no signal at all) it uses the stored values to try running the engine as best as possible, but it will run in a "Fail Safe" mode (aka Limp Mode).

    If you connect a wrong sensor, damage sensor or the sensor reading is not within the factory specs, but the ECM gets some signal, then the engine will will use that signal to start the engine. If the signal is bad, then it won't start.

    FYI there is another hole on the flywheel where the dowel pin can go as well, and it's only a few centimeters from the dowel pin hole.

    Reply to Comment

  • Cory did you ever figure out the problem? I have the exact same issue. My 03 350z Cranks but wont start and I replaced the crank sensor twice along with the camshaft sensors~ Any luck? I'm thinking it's electrical in nature now. The P0335 code shows up after replacing the cranksensor twice = So I hope it's something easy to fix in the electrical

    Reply to Comment

  • Do you have an automatic or manual transmission? have you done anything with the transmission lately?

    Reply to Comment

  • It's a manual transmission and no work has been performed on the trans. I have a full report here http://mechanics.stackexcha...

    Reply to Comment

  • Have you actually check for fuel pressure? (You could just remove the fuel rail line and crank the engine). Does the Security light stays ON while cranking the engine?

    Reply to Comment

  • I have the same exact problem ... Did you ever get it fixed ? What is the procedure to check the sensor?

    Reply to Comment

  • Hi,
    I have a Nissan Lafesta X Japan with MR20DE engine and 2WD CVT gearbox. After replacing the transmission, Car cranks but doesnt want to start. We have tried by putting in a used Crank Shaft sensor since the code is P0335 but it didn't start. Any idea on what next?

    Reply to Comment

  • Did you removed the flywheel? you may have installed the flywheel in the wrong position. That happens all the time.

    Reply to Comment

  • Hi, I have 2002 Nissan March AK12. When I was driving engine stall suddenly. This happen to me several times. Engine check light also on. So I scan the engine and shows this code - P0355 CKP SEN/CIRCUIT. Sensor cleaned and placed. Petrol pump replaced. injectors and plugs cleaned. Then engine check bulb off and vehicle run two days. Now again vehicle stall. engine check bulb on again. after few minutes engine starts. one time engine didn't accelerate. can you please explain the error.
    Thanks.

    Reply to Comment

  • You just clean the Crankshaft Position Sensor, but you probably have to replace the sensor. Usually the problem is inside the sensor.

    Reply to Comment

  • Yesterday I replace the sensor now problem solved. Thanks and best regards.

    Reply to Comment

  • I had code p0335 on my Nissan Murano which is crankshaft sensor I replaced it today now my engine stalls and jerks check engine light came back on reading same code I took the sensor back to auto parts store to exchange thinking the sensor was defected they gave me a new one with no problem I put it on and nothing's changed. Any suggestions?

    Reply to Comment

  • What year is your Murano?

    Reply to Comment

  • 2006

    Reply to Comment

  • The 75% of the times (according to a nation database of repairs) the Crankshaft Position Sensor is the cause of the problem, but in some cases, it's the Camshaft Position Sensor the problem. At my shop we always recommend replacing all 3 sensor (two camshaft and the crankshaft position sensor).

    Reply to Comment

  • Thank you I'll try that tomorrow and let you know how things went!!

    Reply to Comment

  • got the PO335+PO725 Crank pos sensor " Circuit " and TCM engine speed signal codes show up
    Replaced the crank sensor today but still runs horribly. Any clues?

    Reply to Comment

  • hi, i have nissan maxima 2005y. it runs perfect, but car jerking and sometimes engine stall, when i try accelerate. now, error codes are: p1800, p0335, p0550, p1051, p0037, p 1168.
    fuel pump changed, crank sensor changed, thtottle body cleaned. please help me!

    Reply to Comment

  • Of all the codes you listed, only the P0335 code (Crankshaft Position Sensor) will cause the symptom you described. Have you tried clearing the codes? what codes comes back first? did you use a factory Sensor?

    Reply to Comment

  • when i triy clearing p0335, engine stall. all codes cleares, without p1800, and p1051. from deleted codes comes back first p0550 and p0037. after driving comes back p0335. now, i use crankshaft sensor "made in china"

    Reply to Comment

  • I have had bad luck with aftermarket Crankshaft Position Sensors, there is a 50-50 chance that the sensors work or not. I recommend only OEM or OES parts or from known brads like Hitachi.

    P0550 NISSAN - Power Steering Pressure Sensor Circuit Malfunction
    Read more: https://www.autocodes.com/p...

    P0037 NISSAN - HO2S12 Heater Control Circuit Low
    Read more: https://www.autocodes.com/p...

    P1051 NISSAN - Air Fuel Ratio Sensor 1 Heater Control Circuit Low Bank 2
    Read more: https://www.autocodes.com/p...

    Check this vide for the P1800 code, you may be able to fix that.
    https://youtu.be/Rei9wv1RVic

    Reply to Comment

  • thank you, very helpful information!

    Reply to Comment

  • Hi I have a 2008 Nissan Altima 3.5l coupe
    I have changed the crankshaft sensor with factory and the camshaft with aftermarket I have checked wiring and it’s all good and I sent in the ecm to see if it was bad but there was nothing wrong with it. I also changed maf sensor because there was code for it but no more only po335, car runs alright but there’s still something
    I’m at a loss.

    Reply to Comment

  • Other than the Crankshaft Position Sensor I have not seen any other components setting the P0335 code. There are no factory bulletins or recalls either. My only recommendation is to double check the sensor connector. Do you have any other symptoms?

    Reply to Comment