P3467 Dodge Code - Cylinder 9 Deactivation/Intake Valve Control Circuit Low
Quick Answer
The P3467 diagnostic trouble code (DTC) for Dodge vehicles specifically refers to an issue with the Cylinder 9 Deactivation/Intake Valve Control Circuit being detected as low. Common causes include Faulty wiring or connectors in the intake valve control circuit, Malfunctioning intake valve control solenoid, Failed intake valve actuator. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P3467 Dodge indicates Cylinder 9 Deactivation/Intake Valve Control Circuit Low.
- Common causes
- Common causes include Faulty wiring or connectors in the intake valve control circuit, Malfunctioning intake valve control solenoid, Failed intake valve actuator.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
Code P3467 Dodge Description
The P3467 diagnostic trouble code (DTC) for Dodge vehicles specifically refers to an issue with the Cylinder 9 Deactivation/Intake Valve Control Circuit being detected as low. This code is typically found in vehicles equipped with cylinder deactivation technology, which allows the engine to operate on fewer cylinders under light load conditions to improve fuel efficiency.
Common Causes of P3467 Dodge
- Faulty wiring or connectors in the intake valve control circuit
- Malfunctioning intake valve control solenoid
- Failed intake valve actuator
- Issues with the engine control module (ECM)
- Electrical issues such as a blown fuse or short circuit
Symptoms of P3467 Dodge
- Rough idle or engine misfires
- Decreased fuel efficiency
- Loss of power or acceleration
- Illuminated check engine light
- Engine may run in reduced power mode
How to Fix P3467 Dodge
- Begin by conducting a visual inspection of the intake valve control circuit, checking for any damaged wiring or connectors. Repair or replace as needed.
- Test the intake valve control solenoid and actuator for proper operation. Replace any components that are faulty.
- Use a diagnostic scan tool to check for any stored fault codes and perform a thorough diagnosis of the cylinder deactivation system.
- Clear the DTC and reset the ECM to see if the code returns after repairs have been made.
- Test drive the vehicle to ensure that the issue has been resolved and that the engine is running smoothly.
Cost to Fix P3467 Dodge
The typical repair costs for addressing a P3467 DTC can range from $200 to $500, including parts and labor. However, it's essential to note that the specific diagnosis time and labor rates at auto repair shops can vary significantly based on factors such as location, vehicle make and model, and engine type. Auto repair shops commonly charge between $80 and $150 per hour for labor, but rates may be higher in metropolitan areas or at dealerships, while independent shops often charge less. To obtain a more accurate estimate, it's advisable to consult with local auto repair shops.
Need more information about the P3467 Dodge code?
Need more information on how to fix the P3467 Dodge code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P3467 Dodge code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P3467 Dodge Code
What does OBDII code P3467 mean for a Dodge vehicle?
Code P3467 indicates a problem in the Cylinder 9 Deactivation/Intake Valve Control Circuit, where the voltage is lower than expected.
What are the common symptoms of code P3467 in a Dodge?
Symptoms include engine misfires, reduced fuel efficiency, rough idling, and possible activation of the check engine light.
What causes the P3467 code to appear in a Dodge?
Possible causes include a faulty intake valve solenoid, damaged wiring or connectors, low oil pressure, or issues with the engine control module (ECM).
Can a low oil level cause code P3467?
Yes, insufficient oil levels or low oil pressure can affect the operation of the intake valve control system and trigger the P3467 code.
How can I diagnose the P3467 code on my Dodge?
Start by inspecting the intake valve solenoid, wiring, and connectors for damage. Test the solenoid for proper operation, and check oil pressure levels.
Is it safe to drive with the P3467 code active?
Driving with this code can lead to engine performance issues and potential long-term damage. It’s best to address the problem promptly.
How do I fix code P3467 in a Dodge?
Repairs may include replacing the intake valve solenoid, repairing damaged wiring or connectors, changing the oil, or updating/reprogramming the ECM.
How much does it typically cost to fix the P3467 code?
Depending on the cause, repairs can range from $200 to $600, with costs varying for parts, labor, and diagnostics.
Can dirty oil cause code P3467 in a Dodge?
Yes, dirty or degraded oil can interfere with the operation of the intake valve control system and trigger the code.
Will resetting the check engine light clear code P3467 permanently?
No, clearing the code without addressing the underlying issue will result in the code reappearing after a short time.
Discuss the causes and fixes for P3467 Dodge OBDII Code
Code P3467 Dodge comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.