P1253 Ford Code - Pedal Correlation PDS1 and LPDS Low
Quick Answer
The P1253 Ford diagnostic trouble code (DTC) indicates a problem with the correlation between the Pedal Demand Sensor 1 (PDS1) and the Low Power Disabled Strategy (LPDS) in the vehicle's engine control module (ECM). Common causes include Faulty Pedal Demand Sensor 1 (PDS1), Wiring or connector issues between the PDS1 and ECM, ECM software or programming issues. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P1253 Ford indicates Pedal Correlation PDS1 and LPDS Low.
- Common causes
- Common causes include Faulty Pedal Demand Sensor 1 (PDS1), Wiring or connector issues between the PDS1 and ECM, ECM software or programming issues.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
Code P1253 Ford Description
The P1253 Ford diagnostic trouble code (DTC) indicates a problem with the correlation between the Pedal Demand Sensor 1 (PDS1) and the Low Power Disabled Strategy (LPDS) in the vehicle's engine control module (ECM). The PDS1 is responsible for monitoring the driver's demand for engine power by detecting the position of the accelerator pedal. The LPDS, on the other hand, is a strategy used by the ECM to limit engine power when certain conditions are not met or when a fault is detected.
Common Causes of P1253 Ford
- Faulty Pedal Demand Sensor 1 (PDS1)
- Wiring or connector issues between the PDS1 and ECM
- ECM software or programming issues
- Faulty Low Power Disabled Strategy (LPDS)
- Intermittent electrical connection issues
Symptoms of P1253 Ford
- Sluggish acceleration
- Reduced engine power
- Poor fuel efficiency
- Stalling or hesitation while driving
- Vehicle going into limp mode
How to Fix P1253 Ford
- Use a diagnostic scan tool to retrieve the fault codes and verify the P1253 code.
- Inspect the wiring and connectors between the PDS1 and ECM for any damage or corrosion. Repair or replace as necessary.
- Test the Pedal Demand Sensor 1 for proper operation and replace if faulty.
- Check the ECM for any software updates or reprogramming that may be required to address the correlation issue.
- Clear the fault codes and perform a test drive to ensure the issue has been resolved.
Cost to Fix P1253 Ford
The typical repair costs for addressing a P1253 Ford code can range from $200 to $500, depending on the specific cause of the issue and the labor rates at the auto repair shop. Parts such as a new Pedal Demand Sensor 1 or ECM reprogramming may incur additional costs. It is recommended to consult with a qualified mechanic or dealership for a more accurate estimate based on the vehicle's make and model. Keep in mind that diagnostic time and labor rates can vary, so it's advisable to inquire about these factors before proceeding with the repair.
Need more information about the P1253 Ford code?
Need more information on how to fix the P1253 Ford code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P1253 Ford code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P1253 Ford Code
No Frequently Asked Questions about P1253 Ford Code found.
Discuss the causes and fixes for P1253 Ford OBDII Code
Code P1253 Ford comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.