P10B7 2017 GMC Sierra Code - Mass Air Flow Sensor Intake Air Signals Message Counter Incorrect Bank 2
Quick Answer
The P10B7 diagnostic trouble code applies to 2017 GMC Sierra vehicles. Common causes include Faulty MAF sensor, Damaged or disconnected wiring to the MAF sensor, Air leaks in the intake air system. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P10B7 2017 GMC Sierra indicates Mass Air Flow Sensor Intake Air Signals Message Counter Incorrect Bank 2.
- Common causes
- Common causes include Faulty MAF sensor, Damaged or disconnected wiring to the MAF sensor, Air leaks in the intake air system.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
Code P10B7 2017 GMC Sierra Description
The P10B7 diagnostic trouble code applies to 2017 GMC Sierra vehicles. This code indicates a problem with the Mass Air Flow (MAF) Sensor in Bank 2 of the engine. The MAF sensor measures the volume of air entering the engine and relays this information to the Engine Control Unit (ECU), which uses this data to calculate the correct amount of fuel required for optimal combustion. When the P10B7 code is triggered, it means that the MAF sensor's intake air signals counter is incorrect, leading to inaccurate readings being sent to the ECU.
Common Causes of P10B7 2017 GMC Sierra
- Faulty MAF sensor
- Damaged or disconnected wiring to the MAF sensor
- Air leaks in the intake air system
- Dirty or clogged MAF sensor
- Faulty ECU
Symptoms of P10B7 2017 GMC Sierra
- Poor fuel economy
- Reduced engine power
- Engine misfires
- Rough or inconsistent idling
- Check engine light on
How to Fix P10B7 2017 GMC Sierra
- Conduct a visual inspection of the MAF sensor and its wiring for signs of damage or disconnection. If any issues are found, repair or replace the necessary parts.
- Check for air leaks in the intake air system. This can be done by spraying carburetor cleaner around the intake manifold and listening for changes in engine RPM. If a leak is found, it must be repaired.
- Clean the MAF sensor using a special MAF sensor cleaner. This can often resolve issues of dirty or clogged sensors.
- If the MAF sensor itself is faulty, it will need to be replaced.
- If all else fails, the ECU may be at fault and will need to be examined by a professional.
Cost to Fix P10B7 2017 GMC Sierra
The cost of repairing a P10B7 code can vary widely depending on the specific issue. A new MAF sensor can cost between $100 and $400, plus labor. If the issue is related to wiring, the cost could be lower, around $50 to $200. If the ECU is faulty, repairs could run into the thousands of dollars. Most auto repair shops typically charge between $80 and $150 per hour for labor, but this can vary based on location, vehicle make and model, and engine type. It's recommended to check local rates for a more precise estimate.
Need more information about the P10B7 2017 GMC Sierra code?
Need more information on how to fix the P10B7 2017 GMC Sierra code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P10B7 2017 GMC Sierra code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P10B7 2017 GMC Sierra Code
No Frequently Asked Questions about P10B7 2017 GMC Sierra Code found.
Discuss the causes and fixes for P10B7 2017 GMC Sierra OBDII Code
Code P10B7 2017 GMC Sierra comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.