P0699 Jeep Code - Accelerator Pedal Position Sensor Supply Voltage Too High
Quick Answer
The P0699 code for a Jeep indicates that the Accelerator Pedal Position Sensor Supply Voltage is too high. Common causes include Faulty Accelerator Pedal Position Sensor, Wiring or connector issues in the sensor circuit, ECM malfunction. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P0699 Jeep indicates Accelerator Pedal Position Sensor Supply Voltage Too High.
- Common causes
- Common causes include Faulty Accelerator Pedal Position Sensor, Wiring or connector issues in the sensor circuit, ECM malfunction.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
Code P0699 Jeep Description
The P0699 code for a Jeep indicates that the Accelerator Pedal Position Sensor Supply Voltage is too high. This sensor is responsible for monitoring the position of the accelerator pedal and sending this information to the Engine Control Module (ECM) to adjust fuel delivery and ignition timing accordingly. When the supply voltage to the sensor is too high, it can cause incorrect readings and potentially lead to issues with engine performance and drivability.
Common Causes of P0699 Jeep
- Faulty Accelerator Pedal Position Sensor
- Wiring or connector issues in the sensor circuit
- ECM malfunction
- Voltage regulator malfunction
- Battery voltage too high
Symptoms of P0699 Jeep
- Loss of power during acceleration
- Engine stalling or rough idling
- Check Engine Light illuminated on the dashboard
- Reduced fuel efficiency
- Difficulty maintaining a consistent speed
How to Fix P0699 Jeep
- Begin by diagnosing the root cause of the issue using a diagnostic scanner to confirm the P0699 code and identify the specific component causing the problem.
- Inspect the wiring and connectors associated with the Accelerator Pedal Position Sensor for any signs of damage, corrosion, or loose connections. Repair or replace as needed.
- Test the voltage regulator and battery voltage to ensure they are within the specified range. Replace any faulty components.
- If the sensor itself is faulty, replace it with a new one following the manufacturer's guidelines.
- Clear the trouble codes from the ECM and perform a road test to verify that the issue has been resolved.
Cost to Fix P0699 Jeep
The typical repair costs for addressing a P0699 code in a Jeep can vary depending on the specific cause of the issue and the parts needed for the repair. On average, the cost of replacing an Accelerator Pedal Position Sensor can range from $100 to $300, including parts and labor. However, additional costs may apply if other components need to be replaced or if further diagnostics are required. It is recommended to consult with a certified mechanic or auto repair shop to get an accurate estimate based on the vehicle's make and model. Labor rates at auto repair shops can range from $80 to $150 per hour, with rates potentially higher at dealerships or in metropolitan areas.
Need more information about the P0699 Jeep code?
Need more information on how to fix the P0699 Jeep code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P0699 Jeep code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P0699 Jeep Code
No Frequently Asked Questions about P0699 Jeep Code found.
Discuss the causes and fixes for P0699 Jeep OBDII Code
Code P0699 Jeep comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.