P0689 Jeep Code - Auto Shutdown Relay Control Circuit Low
Quick Answer
The P0689 code for Jeep vehicles indicates a problem with the Auto Shutdown Relay Control Circuit being detected as low. Common causes include Damaged or corroded wiring in the Auto Shutdown Relay Control Circuit, Faulty Auto Shutdown Relay, Blown fuse related to the circuit. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- P0689 Jeep indicates Auto Shutdown Relay Control Circuit Low.
- Common causes
- Common causes include Damaged or corroded wiring in the Auto Shutdown Relay Control Circuit, Faulty Auto Shutdown Relay, Blown fuse related to the circuit.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
Code P0689 Jeep Description
The P0689 code for Jeep vehicles indicates a problem with the Auto Shutdown Relay Control Circuit being detected as low. The Auto Shutdown Relay is an essential component of the vehicle's electrical system that controls the power supply to the engine control module (ECM) and fuel injectors. When this circuit is operating correctly, it ensures that power is supplied to the ECM and fuel injectors when the ignition key is turned on, allowing the engine to start and run smoothly. However, when the circuit is detected as low, it means that there is a malfunction or a short circuit that is preventing the relay from functioning properly.
Common Causes of P0689 Jeep
- Damaged or corroded wiring in the Auto Shutdown Relay Control Circuit
- Faulty Auto Shutdown Relay
- Blown fuse related to the circuit
- Malfunctioning Engine Control Module (ECM)
- Poor electrical connections or grounds
Symptoms of P0689 Jeep
- Engine stalling or cutting out
- Difficulty starting the engine
- Engine misfires or runs rough
- Check Engine Light illuminated
- Loss of power while driving
How to Fix P0689 Jeep
- Begin by diagnosing the exact cause of the issue using a diagnostic scanner to read the fault code and pinpoint the faulty component.
- Inspect the wiring and connections in the Auto Shutdown Relay Control Circuit for any damage or corrosion. Repair or replace any damaged wires.
- Check the Auto Shutdown Relay and replace it if it is found to be faulty.
- Inspect and replace any blown fuses related to the circuit.
- If the issue persists, have the ECM tested and potentially replaced if it is malfunctioning.
Cost to Fix P0689 Jeep
The typical repair costs for addressing the P0689 code can vary depending on the specific cause of the issue and the labor rates in your area. On average, the repair for this issue can range from $100 to $300, including parts and labor. It's important to note that diagnosis time and labor rates can vary, so it's recommended to get quotes from multiple auto repair shops to get a more accurate estimate. Labor rates at auto repair shops typically range from $80 to $150 per hour, but rates may be higher at dealerships or in metropolitan areas.
Tech Notes for P0689 Jeep
Need more information about the P0689 Jeep code?
Need more information on how to fix the P0689 Jeep code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the P0689 Jeep code diagnosed by a professional: Find a repair shop in your area
Frequently Asked Questions about P0689 Jeep Code
No Frequently Asked Questions about P0689 Jeep Code found.
Discuss the causes and fixes for P0689 Jeep OBDII Code
Code P0689 Jeep comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.