B2738 Jeep Code - Center Pedestrian Protection Satellite Acceleration Sensor
Quick Answer
The B2738 diagnostic trouble code for Jeep vehicles refers to an issue with the Center Pedestrian Protection Satellite Acceleration Sensor. Common causes include Sensor malfunction due to electrical issues, Physical damage to the sensor caused by impact or corrosion, Faulty wiring or connections. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- B2738 Jeep indicates Center Pedestrian Protection Satellite Acceleration Sensor.
- Common causes
- Common causes include Sensor malfunction due to electrical issues, Physical damage to the sensor caused by impact or corrosion, Faulty wiring or connections.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
Code B2738 Jeep Description
The B2738 diagnostic trouble code for Jeep vehicles refers to an issue with the Center Pedestrian Protection Satellite Acceleration Sensor. This sensor is a crucial component of the vehicle's safety system, specifically designed to detect sudden changes in acceleration that could indicate a collision with a pedestrian. When this sensor malfunctions or fails, it can have serious implications for the vehicle's safety features and overall performance.
Common Causes of B2738 Jeep
- Sensor malfunction due to electrical issues.
- Physical damage to the sensor caused by impact or corrosion.
- Faulty wiring or connections.
- Issues with the safety control module.
Symptoms of B2738 Jeep
- Illumination of the airbag warning light on the dashboard.
- Inaccurate or erratic readings from the sensor.
- Unintended airbag deployment.
- Pedestrian protection system failure.
How to Fix B2738 Jeep
- Begin by conducting a thorough inspection of the sensor and its wiring to check for any visible damage or corrosion.
- Test the sensor using a multimeter to determine if it is sending accurate readings to the safety control module.
- If the sensor is faulty, replace it with a new OEM sensor to ensure proper functioning.
- Clear the diagnostic trouble code from the vehicle's system using a diagnostic scanner.
- Test drive the vehicle to ensure that the issue has been resolved and that the sensor is functioning correctly.
Cost to Fix B2738 Jeep
The cost of repairing the Center Pedestrian Protection Satellite Acceleration Sensor can vary depending on the make and model of the vehicle, as well as the labor rates in your area. On average, the parts for this repair can range from $150 to $300, while the labor costs can add an additional $100 to $200. It's important to note that these are rough estimates, and actual costs may vary. Be sure to consult with a qualified mechanic or auto repair shop for a more accurate quote based on your specific vehicle and location.
Tech Notes for B2738 Jeep
B2738-78 CENTER PEDESTRIAN PROTECTION SATELLITE SENSOR ALIGNMENT OR ADJUSTMENT INCORRECT
Need more information about the B2738 Jeep code?
Need more information on how to fix the B2738 Jeep code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the B2738 Jeep code diagnosed by a professional: Find a repair shop in your area
Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service
- Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
- Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
- Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
- Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.
Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.
Frequently Asked Questions about B2738 Jeep Code
1. What are the common symptoms of OBDII code B2738 in a Jeep related to the Center Pedestrian Protection Satellite Acceleration Sensor?
- Common symptoms include illuminated warning lights on the dashboard, reduced vehicle performance, and potential issues with the pedestrian protection system.
2. What typically causes the OBDII code B2738 to trigger in a Jeep's Center Pedestrian Protection Satellite Acceleration Sensor?
- The code is often triggered by a malfunction or failure of the acceleration sensor itself, wiring issues, or problems with the pedestrian protection system.
3. How can I diagnose the cause of OBDII code B2738 related to the Center Pedestrian Protection Satellite Acceleration Sensor in my Jeep?
- Diagnosis involves using a diagnostic scanner to read the specific fault codes, conducting a visual inspection of the sensor and wiring, and testing the sensor's functionality.
4. Is it safe to continue driving my Jeep if OBDII code B2738 related to the Center Pedestrian Protection Satellite Acceleration Sensor is present?
- It is not recommended to drive the vehicle with this code active, as it may indicate potential safety issues with the pedestrian protection system.
5. Can I reset the OBDII code B2738 related to the Center Pedestrian Protection Satellite Acceleration Sensor in my Jeep on my own?
- While you can clear the code with a diagnostic scanner, it is important to address the underlying issue causing the code to prevent it from reoccurring.
6. How much does it typically cost to repair OBDII code B2738 related to the Center Pedestrian Protection Satellite Acceleration Sensor in a Jeep?
- Repair costs can vary depending on the root cause of the issue, but it may involve sensor replacement, wiring repairs, or system diagnostics by a qualified technician.
7. Are there any DIY tips for troubleshooting OBDII code B2738 in a Jeep's Center Pedestrian Protection Satellite Acceleration Sensor?
- DIY tips may include checking for loose or damaged wiring, ensuring sensor connections are secure, and consulting the vehicle's manual for specific troubleshooting steps.
8. Can a faulty Center Pedestrian Protection Satellite Acceleration Sensor affect the overall safety of my Jeep?
- Yes, a malfunctioning sensor can impact the proper functioning of the pedestrian protection system, potentially compromising safety in certain situations.
9. How long does it typically take to repair OBDII code B2738 related to the Center Pedestrian Protection Satellite Acceleration Sensor in a Jeep?
- Repair times can vary based on the complexity of the issue, but it may take anywhere from a few hours to a day for diagnosis and repair.
10. Is it necessary to visit a dealership for repairs related to OBDII code B2738 in a Jeep's Center Pedestrian Protection Satellite Acceleration Sensor?
- While a dealership may have specialized knowledge and tools for these repairs, independent automotive shops with experience in handling similar issues can also effectively address the problem.
Discuss the causes and fixes for B2738 Jeep OBDII Code
Code B2738 Jeep comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.