B1B84 Chrysler Code - Passenger Seat Weight Sensor 2 Left Rear Input Circuit High
Quick Answer
The B1B84 Chrysler code indicates a problem with the Passenger Seat Weight Sensor 2 Left Rear Input Circuit being too high. Common causes include Faulty Passenger Seat Weight Sensor, Damaged wiring harness, Loose or corroded connections. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- B1B84 Chrysler indicates Passenger Seat Weight Sensor 2 Left Rear Input Circuit High.
- Common causes
- Common causes include Faulty Passenger Seat Weight Sensor, Damaged wiring harness, Loose or corroded connections.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
Code B1B84 Chrysler Description
The B1B84 Chrysler code indicates a problem with the Passenger Seat Weight Sensor 2 Left Rear Input Circuit being too high. This sensor is responsible for detecting the weight of the passenger seated in the left rear seat of the vehicle. The sensor is crucial for the proper functioning of the vehicle's airbag system, as it helps determine whether or not to deploy the airbags in the event of a collision.
Common Causes of B1B84 Chrysler
- Faulty Passenger Seat Weight Sensor
- Damaged wiring harness
- Loose or corroded connections
- Electronic control module issues
- Physical damage to the sensor or wiring
Symptoms of B1B84 Chrysler
- Airbag warning light illuminated on the dashboard
- Inaccurate or erratic airbag deployment
- Passenger airbag not deploying in a collision
- Safety system warning messages on the instrument cluster
- Intermittent issues with the airbag system
How to Fix B1B84 Chrysler
- Begin by diagnosing the specific cause of the code, using a diagnostic scanner to read and interpret the fault codes.
- Inspect the Passenger Seat Weight Sensor, wiring harness, and connections for any visible damage or defects.
- Test the sensor's resistance using a multimeter to determine if it is functioning within the manufacturer's specifications.
- If the sensor is faulty, replace it with a new one and recalibrate the system as per the manufacturer's instructions.
- Clear the fault codes from the vehicle's computer system and test the airbag system to ensure proper functionality.
Cost to Fix B1B84 Chrysler
The cost of repairing the B1B84 Chrysler code can vary depending on the specific cause of the issue and the parts needed for the repair. On average, the cost of replacing a Passenger Seat Weight Sensor can range from $200 to $500, including parts and labor. Additional costs may apply if there are other underlying issues that need to be addressed. It is advisable to consult with a trusted mechanic or dealership to get an accurate estimate for the repair.
Need more information about the B1B84 Chrysler code?
Need more information on how to fix the B1B84 Chrysler code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the B1B84 Chrysler code diagnosed by a professional: Find a repair shop in your area
Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service
- Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
- Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
- Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
- Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.
Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.
Frequently Asked Questions about B1B84 Chrysler Code
1. What does OBDII code B1B84 mean on a Chrysler vehicle?
Code B1B84 indicates an issue with the Passenger Seat Weight Sensor 2 Left Rear Input Circuit being detected as high, which may affect the airbag system's functionality.
2. What are the common symptoms of the B1B84 code?
Symptoms include the airbag warning light illuminating, potential deactivation of the passenger airbag, and possible error messages related to the occupant classification system.
3. What causes the B1B84 code to be triggered?
Common causes include a faulty seat weight sensor, damaged wiring or connectors in the circuit, or issues with the Occupant Classification Module (OCM).
4. Can I drive my Chrysler with the B1B84 code active?
While the vehicle may still be drivable, the passenger airbag might not deploy in a collision, posing a safety risk. It's recommended to address the issue promptly.
5. How do I diagnose the B1B84 code?
Begin by scanning the vehicle with an OBDII scanner to confirm the code. Then, inspect the wiring and connectors for damage, test the weight sensor, and check the OCM for faults.
6. How do I fix the B1B84 code?
Repairs may include replacing the faulty weight sensor, repairing or replacing damaged wiring, or recalibrating or replacing the Occupant Classification Module.
7. How much does it cost to fix the B1B84 code on a Chrysler?
The repair cost varies depending on the issue. Replacing a weight sensor may cost $200–$400, while more extensive repairs like module replacement can exceed $500.
8. Can a loose connection cause the B1B84 code?
Yes, a loose or corroded connector in the seat sensor wiring can cause the circuit to read as high and trigger the code.
9. Do I need to recalibrate the system after fixing the B1B84 code?
In most cases, recalibrating the Occupant Classification System is necessary after repairs to ensure proper airbag functionality.
10. Can I clear the B1B84 code without fixing the problem?
Clearing the code without addressing the root cause will likely result in the code returning, and the airbag system may remain compromised.
Discuss the causes and fixes for B1B84 Chrysler OBDII Code
Code B1B84 Chrysler comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.