Engine-Codes.com
Engine-Codes – Generic – B1B08

B1B08 Code - Passenger Airbag Squib 1 Circuit Low

Quick Answer

The B1B08 diagnostic trouble code (DTC) indicates an issue with the Passenger Airbag Squib 1 Circuit being detected as low. Common causes include Faulty passenger airbag squib, Damaged wiring or connectors in the airbag circuit, Blown fuse related to the airbag system. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

What it means
B1B08 indicates Passenger Airbag Squib 1 Circuit Low.
Common causes
Common causes include Faulty passenger airbag squib, Damaged wiring or connectors in the airbag circuit, Blown fuse related to the airbag system.
Severity
High - diagnose this code as soon as possible.
Can I drive?
Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
What is this?
Table of contents Created and updated by William Orellana on Sep 14, 2024
💬 Need more help? Ask Auto Expert for instant answers — it's free!
AutoCodes App

Fix Your Car Smarter

Try the New AutoCodes App!

Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.

AutoCodes App on Google Play

Code B1B08 Description

The B1B08 diagnostic trouble code (DTC) indicates an issue with the Passenger Airbag Squib 1 Circuit being detected as low. The airbag squib is a component of the airbag system that is responsible for inflating the airbag in the event of a collision. When the circuit is detected as low, it means that there is a problem with the electrical connection or signal in the circuit that controls the deployment of the passenger airbag. This can potentially lead to the airbag not deploying properly in the event of a crash, compromising the safety of the vehicle occupants.

OBDII Code B1B08 - Passenger Airbag Squib 1 Circuit Low
B1B08 Code - Passenger Airbag Squib 1 Circuit Low

Common Causes of B1B08

  1. Faulty passenger airbag squib.
  2. Damaged wiring or connectors in the airbag circuit.
  3. Blown fuse related to the airbag system.
  4. Malfunctioning airbag control module.
  5. Corrosion or poor connections in the airbag system components.

Symptoms of B1B08

  1. Illuminated airbag warning light on the dashboard.
  2. Inability to turn off the passenger airbag.
  3. Intermittent or non-deployment of the passenger airbag during a crash.
  4. Diagnostic trouble code stored in the vehicle's computer system.
  5. Loss of communication with the airbag control module.

How to Fix B1B08

  1. Begin by diagnosing the specific cause of the issue using a diagnostic scanner to retrieve the DTC and pinpoint the faulty component.
  2. Inspect the wiring and connectors in the airbag circuit for any damage or corrosion. Repair or replace as necessary.
  3. Check and replace any blown fuses related to the airbag system.
  4. Test the passenger airbag squib for proper functionality and replace if found to be faulty.
  5. Clear the DTC from the vehicle's computer system and perform a test to ensure that the issue has been resolved.

Cost to Fix B1B08

The typical repair costs for addressing a Passenger Airbag Squib 1 Circuit Low issue can vary depending on the specific cause of the problem and the cost of parts and labor. On average, the repair for this type of issue can range from $200 to $500, including parts and labor. However, it is important to note that the actual cost may vary based on factors such as the location of the repair shop, the make and model of the vehicle, and the extent of the repairs needed. It is recommended to consult with a qualified mechanic or repair shop to obtain a more accurate estimate based on your specific circumstances.

When is the Code Detected?

This Diagnostic Trouble Code (DTC) sets when the ORC detects a short to ground on the squib circuit for more than 2.5 seconds. This DTC transitions from active to stored when the ORC sees a recovery from a short to ground condition for greater than 2.5 seconds.

Need more information about the B1B08 code?

Need more information on how to fix the B1B08 code? Get Access to Factory Service Manuals

Need Help with the Code?

Get the B1B08 code diagnosed by a professional: Find a repair shop in your area

Code B1B08 Information for Specific Makes

Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service

  • Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
  • Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
  • Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
  • Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.

Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.

About the author: William Orellana is a Master Mechanic and Mechanical Engineer with over 30 years of experience diagnosing and repairing vehicles. Learn more about his background.

Frequently Asked Questions about B1B08 Code

1. What does the OBDII code B1B08 mean?

The code B1B08 indicates a low voltage issue in the passenger airbag squib 1 circuit, which is part of the airbag deployment system.

2. What are the common symptoms of the B1B08 code?

Symptoms may include the airbag warning light illuminating on the dashboard and the passenger airbag potentially being disabled.

3. What causes the B1B08 code to appear?

Common causes include damaged wiring, a faulty passenger airbag squib, a bad clock spring, loose connectors, or a malfunctioning airbag control module.

4. Is it safe to drive with a B1B08 code?

It is not recommended to drive with this code as the airbag system may not function correctly in the event of an accident.

5. How can I diagnose the B1B08 code?

Start by inspecting the wiring and connectors for the passenger airbag squib, then use a scan tool to test the airbag system circuits for continuity and resistance.

6. Can the B1B08 code be cleared without fixing the issue?

Clearing the code without repairing the underlying issue may temporarily reset the warning light, but the code will likely return, and the airbag system may remain compromised.

7. How much does it cost to fix the B1B08 code?

Repair costs vary depending on the issue, ranging from $50 for a simple wiring fix to $1,000 or more for replacing the airbag control module or squib.

8. What tools are needed to troubleshoot the B1B08 code?

You’ll need a professional-grade OBDII scanner with airbag system capabilities, a multimeter, and possibly a wiring diagram for your vehicle.

9. Can I fix the B1B08 code myself?

If you have experience with automotive electronics and safety systems, you may be able to address simple issues like damaged wiring. However, airbag repairs are best left to professionals due to safety risks.

10. What happens if I ignore the B1B08 code?

Ignoring this code could result in the passenger airbag failing to deploy in an accident, increasing the risk of injury to the passenger.

Discuss the causes and fixes for B1B08 OBDII Code

Submit a New Comment

Code B1B08 comments

No comments found for this page.