B1980 Code - Bulb Outage Condition Detected
Quick Answer
The B1980 diagnostic trouble code indicates that a bulb outage condition has been detected in the vehicle. Common causes include Burnt-out bulb, Loose or corroded electrical connections, Faulty wiring harness. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- B1980 indicates Bulb Outage Condition Detected.
- Common causes
- Common causes include Burnt-out bulb, Loose or corroded electrical connections, Faulty wiring harness.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
Code B1980 Description
The B1980 diagnostic trouble code indicates that a bulb outage condition has been detected in the vehicle. This means that one or more of the bulbs in the vehicle's lighting system, such as the headlights, taillights, brake lights, turn signals, or interior lights, are not functioning properly. This issue can significantly impact the safety of the vehicle, as proper lighting is essential for visibility on the road, especially in low-light conditions or at night.
Common Causes of B1980
- Burnt-out bulb
- Loose or corroded electrical connections
- Faulty wiring harness
- Blown fuse
- Malfunctioning control module
Symptoms of B1980
- Dashboard warning light indicating bulb outage
- Dim or flickering lights
- Inoperative turn signals
- Reduced visibility at night
- Potential citation from law enforcement
How to Fix B1980
- Identify the faulty bulb by visually inspecting all exterior and interior lights.
- Replace the burnt-out bulb with a new one of the same type and voltage.
- Check and clean any corroded electrical connections to ensure a secure connection.
- Test the circuit with a multimeter to verify proper continuity.
- Reset the vehicle's monitoring system to clear the error code.
Cost to Fix B1980
The cost of repairing a bulb outage condition detected by the B1980 code can vary depending on the specific bulb that needs replacement, the vehicle make and model, and labor rates in your area. On average, the cost of a new bulb can range from $5 to $50, while the labor cost for bulb replacement may be around $50 to $100 per hour. Overall, the total repair cost for this issue typically ranges from $50 to $200. It's recommended to consult with a professional mechanic to get an accurate estimate for your specific situation.
Need more information about the B1980 code?
Need more information on how to fix the B1980 code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the B1980 code diagnosed by a professional: Find a repair shop in your area
Code B1980 Information for Specific Makes
- B1980 Chrysler — Power Liftgate Latch Control 1 Circuit Low
- B1980 Dodge — Power Liftgate Latch Control 1 Circuit Low
- B1980 Jeep — Power Liftgate Latch Control 1 Circuit Low
- B1980 RAM — Power Liftgate Latch Control 1 Circuit Low
Frequently Asked Questions about B1980 Code
1. What are the common symptoms of OBDII code B1980 (Bulb Outage Condition Detected)?
- The most common symptom is the illumination of the bulb warning light on the dashboard indicating a fault with one or more vehicle bulbs.
2. What are the possible causes of OBDII code B1980?
- The code B1980 is typically triggered when the vehicle's monitoring system detects a discrepancy between the expected and actual electrical current consumption of a bulb, indicating a potential bulb outage.
3. How can I diagnose the source of OBDII code B1980?
- Start by visually inspecting all exterior and interior bulbs for any signs of damage or burnt-out filaments. Use a multimeter to test the electrical continuity of each bulb to identify the faulty one.
4. Can OBDII code B1980 be triggered by a loose bulb connection?
- Yes, a loose or improperly connected bulb can also trigger code B1980. Ensure all bulbs are securely in place and the connections are clean and free from corrosion.
5. Is it necessary to replace the entire light assembly if OBDII code B1980 is detected?
- Not necessarily. In most cases, simply replacing the faulty bulb or repairing the connection issue should resolve the code B1980 and restore proper bulb operation.
6. Are aftermarket bulbs compatible with the vehicle's monitoring system for OBDII code B1980?
- It is recommended to use OEM-equivalent or high-quality replacement bulbs to ensure compatibility with the vehicle's monitoring system and prevent false fault codes like B1980.
7. Can extreme weather conditions trigger OBDII code B1980?
- Yes, extreme temperatures or moisture can sometimes cause electrical issues with bulbs, leading to the triggering of code B1980. Ensure bulbs are properly sealed and protected from the elements.
8. Should I reset the OBDII code B1980 after replacing a faulty bulb?
- Yes, it is recommended to reset the fault code using an OBDII scanner after addressing the bulb outage issue. This will clear the warning light and verify the successful repair.
9. How can I prevent OBDII code B1980 from recurring in the future?
- Regularly inspect and maintain all vehicle bulbs to ensure they are in good working condition. Promptly replace any faulty bulbs to prevent the recurrence of code B1980.
10. Can code B1980 affect the overall safety of the vehicle?
- While code B1980 itself does not directly impact the vehicle's safety, driving with malfunctioning bulbs can reduce visibility to other drivers and compromise road safety. It is essential to address this issue promptly.
Discuss the causes and fixes for B1980 OBDII Code
Code B1980 comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.