B1940 2018 Toyota RAV4 Code - Short in Selectable Force Limiter Squib Right Circuit
Quick Answer
The B1940 diagnostic trouble code (DTC) for a 2018 Toyota RAV4 indicates a short in the Selectable Force Limiter Squib Right Circuit. Common causes include Damaged wiring or connectors in the Selectable Force Limiter Squib Right Circuit, Faulty force limiter squib component, Corrosion in the electrical connections. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- B1940 2018 Toyota RAV4 indicates Short in Selectable Force Limiter Squib Right Circuit.
- Common causes
- Common causes include Damaged wiring or connectors in the Selectable Force Limiter Squib Right Circuit, Faulty force limiter squib component, Corrosion in the electrical connections.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
Code B1940 2018 Toyota RAV4 Description
The B1940 diagnostic trouble code (DTC) for a 2018 Toyota RAV4 indicates a short in the Selectable Force Limiter Squib Right Circuit. This code is related to the vehicle's supplemental restraint system (SRS), specifically the force limiter squib on the right side. The force limiter squib is a component of the seatbelt system that helps to control the amount of force applied to the occupant in the event of a collision.
Common Causes of B1940 2018 Toyota RAV4
- Damaged wiring or connectors in the Selectable Force Limiter Squib Right Circuit
- Faulty force limiter squib component
- Corrosion in the electrical connections
- Impact or collision that damaged the seatbelt system
- Manufacturing defect in the SRS components
Symptoms of B1940 2018 Toyota RAV4
- Airbag warning light illuminated on the dashboard
- Inability to engage or disengage the seatbelt
- Erratic behavior of the seatbelt retractor
- SRS system failure message on the instrument cluster
How to Fix B1940 2018 Toyota RAV4
- Begin by disconnecting the vehicle's battery to prevent accidental deployment of the airbags.
- Inspect the wiring and connectors associated with the Selectable Force Limiter Squib Right Circuit for any damage or corrosion. Repair or replace as necessary.
- Test the force limiter squib component to determine if it is functioning correctly. Replace if faulty.
- Clear the DTC from the vehicle's memory using a diagnostic scan tool.
- Reconnect the battery and test the SRS system to ensure proper functionality.
Cost to Fix B1940 2018 Toyota RAV4
The cost of repairing a short in the Selectable Force Limiter Squib Right Circuit can vary depending on the extent of the damage and the specific components that need to be replaced. In general, the parts for this repair may range from $100 to $300, while the labor costs can be between $150 and $300. Overall, the total repair cost could fall between $250 and $600. It is important to note that these are rough estimates, and actual costs may differ based on the location, vehicle make and model, and labor rates at the auto repair shop. It is recommended to obtain a detailed quote from a qualified mechanic before proceeding with the repair.
Need more information about the B1940 2018 Toyota RAV4 code?
Need more information on how to fix the B1940 2018 Toyota RAV4 code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the B1940 2018 Toyota RAV4 code diagnosed by a professional: Find a repair shop in your area
Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service
- Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
- Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
- Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
- Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.
Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.
Frequently Asked Questions about B1940 2018 Toyota RAV4 Code
1. What are the common symptoms of OBDII code B1940 in a 2018 Toyota RAV4?
- Common symptoms include the airbag warning light being illuminated on the dashboard and potential issues with the airbag system's functionality.
2. What does the OBDII code B1940 ("Short in Selectable Force Limiter Squib Right Circuit") indicate in a 2018 Toyota RAV4?
- This code indicates a short circuit in the selectable force limiter squib circuit on the right side of the vehicle's airbag system.
3. What are the possible causes of OBDII code B1940 in a 2018 Toyota RAV4?
- Possible causes include damaged wiring or connectors in the selectable force limiter squib circuit, a faulty squib unit, or issues with the airbag control module.
4. How can I diagnose the source of OBDII code B1940 in my 2018 Toyota RAV4?
- Proper diagnosis involves inspecting the wiring and connectors in the selectable force limiter squib circuit, testing the squib unit for resistance, and checking the airbag control module for faults.
5. Is it safe to drive my 2018 Toyota RAV4 with OBDII code B1940 active?
- It is not recommended to drive the vehicle with this code active, as it indicates a potential issue with the airbag system, which could affect its proper function in the event of an accident.
6. Can I fix OBDII code B1940 in my 2018 Toyota RAV4 by resetting the airbag system?
- Resetting the airbag system may temporarily clear the code, but it will not fix the underlying issue causing the short in the selectable force limiter squib right circuit.
7. How much does it typically cost to repair OBDII code B1940 in a 2018 Toyota RAV4?
- The cost of repair can vary depending on the specific cause of the issue, but it may involve replacing damaged wiring, connectors, or components in the airbag system.
8. Are there any safety concerns associated with OBDII code B1940 in a 2018 Toyota RAV4?
- Yes, there are safety concerns as this code relates to the airbag system, which is a critical safety feature in the vehicle. It's important to address this issue promptly.
9. Can I repair OBDII code B1940 in my 2018 Toyota RAV4 myself, or do I need to take it to a professional mechanic?
- Repairing this code typically requires specialized knowledge and tools related to the airbag system. It is recommended to have a professional mechanic diagnose and repair the issue.
10. How long does it usually take to repair OBDII code B1940 in a 2018 Toyota RAV4?
- The repair time can vary depending on the exact cause of the issue and the availability of parts. In general, it may take a few hours to a full day to address this code properly.
Discuss the causes and fixes for B1940 2018 Toyota RAV4 OBDII Code
Code B1940 2018 Toyota RAV4 comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.