B1922 Code - Air Bag Safing Sensor Output Circuit Short To Battery
Quick Answer
The B1922 diagnostic trouble code refers to an issue with the airbag safing sensor output circuit being shorted to the battery. Common causes include Wiring issues, such as a short circuit or damaged wiring harness, Faulty airbag safing sensor, Corrosion or damage to the connectors in the airbag system. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- B1922 indicates Air Bag Safing Sensor Output Circuit Short To Battery.
- Common causes
- Common causes include Wiring issues, such as a short circuit or damaged wiring harness, Faulty airbag safing sensor, Corrosion or damage to the connectors in the airbag system.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
Code B1922 Description
The B1922 diagnostic trouble code refers to an issue with the airbag safing sensor output circuit being shorted to the battery. The airbag safing sensor is a crucial component of the vehicle's airbag system, responsible for detecting sudden deceleration and deploying the airbags in the event of a collision. When this circuit is shorted to the battery, it can disrupt the proper functioning of the airbag system, potentially preventing the airbags from deploying when needed.
Common Causes of B1922
- Wiring issues, such as a short circuit or damaged wiring harness.
- Faulty airbag safing sensor.
- Corrosion or damage to the connectors in the airbag system.
- Issues with the airbag control module.
- Electrical problems within the vehicle's system.
Symptoms of B1922
- Airbag warning light illuminated on the dashboard.
- Inability to turn off the airbag warning light even after resetting it.
- Failure of the airbags to deploy in a collision.
- Erratic behavior of the airbag system, such as unintended deployment or failure to deploy.
How to Fix B1922
- Begin by diagnosing the exact cause of the issue by using a diagnostic scanner to retrieve the trouble codes and pinpoint the source of the problem.
- Inspect the wiring and connectors in the airbag system for any signs of damage, corrosion, or loose connections. Repair or replace any damaged components as needed.
- Test the airbag safing sensor to determine if it is functioning correctly. Replace the sensor if it is found to be faulty.
- Clear the trouble codes from the vehicle's system and reset the airbag warning light.
- Perform a thorough test of the airbag system to ensure that it is functioning properly after the repairs have been completed.
Cost to Fix B1922
The cost of repairing a B1922 code can vary depending on the specific cause of the issue and the labor rates at the auto repair shop. On average, the repair cost for this issue can range from $150 to $500, including parts and labor. However, it's important to note that the diagnosis time and labor rates at auto repair shops can vary significantly, so it's advisable to check with local shops for a more accurate estimate. Additionally, factors such as the vehicle make and model, location, and the severity of the issue can also impact the overall cost of the repair.
Need more information about the B1922 code?
Need more information on how to fix the B1922 code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the B1922 code diagnosed by a professional: Find a repair shop in your area
Code B1922 Information for Specific Makes
- B1922 Lexus — Short To Ground In Rear Pretensioner Squib RH Circuit
- B1922 Scion — Short To Ground In Rear Pretensioner Squib RH Circuit
- B1922 Toyota — Short To Ground In Rear Pretensioner Squib RH Circuit
Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service
- Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
- Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
- Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
- Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.
Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.
Frequently Asked Questions about B1922 Code
1. What are the common symptoms of OBDII code B1922?
- The common symptoms of code B1922 include the airbag warning light illuminated on the dashboard and potential issues with the airbag system's functionality.
2. What does the OBDII code B1922 indicate?
- OBDII code B1922 indicates a problem with the Air Bag Safing Sensor Output Circuit, specifically a short to the battery.
3. What can cause the Air Bag Safing Sensor Output Circuit to short to the battery?
- The Air Bag Safing Sensor Output Circuit can short to the battery due to damaged wiring, faulty connectors, or a malfunctioning airbag safing sensor.
4. How serious is OBDII code B1922?
- OBDII code B1922 is a serious issue as it indicates a potential problem with the airbag system, which may affect its proper deployment in case of an accident.
5. Can I continue driving with OBDII code B1922 present?
- It is not recommended to continue driving with OBDII code B1922 present, as it may compromise the functionality of the airbag system and put your safety at risk.
6. How can I diagnose and repair OBDII code B1922?
- Diagnosing and repairing OBDII code B1922 typically involves inspecting the wiring and connectors in the Air Bag Safing Sensor Output Circuit, repairing any damaged components, and clearing the code with a scan tool.
7. Can I reset OBDII code B1922 on my own?
- You can attempt to reset OBDII code B1922 on your own using an OBDII scan tool, but it is important to address the underlying issue causing the code to prevent it from reoccurring.
8. Are there any safety precautions to keep in mind when dealing with OBDII code B1922?
- When working on the airbag system related to OBDII code B1922, always disconnect the vehicle's battery and wait for the system to fully discharge before starting any repairs to avoid accidental airbag deployment.
9. How much does it typically cost to repair OBDII code B1922?
- The cost to repair OBDII code B1922 can vary depending on the extent of the damage and the specific components that need to be replaced, but it is advisable to consult with a professional mechanic for an accurate estimate.
10. Can OBDII code B1922 be a recurring issue?
- OBDII code B1922 can be a recurring issue if the underlying cause, such as damaged wiring or a faulty sensor, is not properly addressed during the repair process. Regular maintenance and thorough diagnostics can help prevent its recurrence.
Discuss the causes and fixes for B1922 OBDII Code
Code B1922 comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.