B1908 2016 Toyota RAV4 Code - Short to Positive in Front Pretensioner Squib Left Circuit
Quick Answer
The B1908 diagnostic trouble code (DTC) for the 2016 Toyota RAV4 indicates a short to positive in the front pretensioner squib left circuit. Common causes include Wiring issues, such as a short circuit or damaged wiring harness, Faulty front pretensioner squib, Corrosion or poor connections in the electrical system. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- B1908 2016 Toyota RAV4 indicates Short to Positive in Front Pretensioner Squib Left Circuit.
- Common causes
- Common causes include Wiring issues, such as a short circuit or damaged wiring harness, Faulty front pretensioner squib, Corrosion or poor connections in the electrical system.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
Code B1908 2016 Toyota RAV4 Description
The B1908 diagnostic trouble code (DTC) for the 2016 Toyota RAV4 indicates a short to positive in the front pretensioner squib left circuit. This code is related to the vehicle's safety restraint system, specifically the pretensioner system in the driver's side seatbelt. The pretensioner is a crucial component that tightens the seatbelt in the event of a collision, helping to restrain the occupant and minimize injuries.
Common Causes of B1908 2016 Toyota RAV4
- Wiring issues, such as a short circuit or damaged wiring harness
- Faulty front pretensioner squib
- Corrosion or poor connections in the electrical system
- Vehicle impact or collision causing damage to the pretensioner system
- Electrical interference or malfunctions in the vehicle's electrical system
Symptoms of B1908 2016 Toyota RAV4
- Illumination of the airbag warning light on the dashboard
- Inability of the pretensioner system to tighten the seatbelt during a sudden stop or collision
- Diagnostic trouble code B1908 stored in the vehicle's computer
- Erratic behavior of the seatbelt mechanism
How to Fix B1908 2016 Toyota RAV4
- Begin by disconnecting the vehicle's battery to prevent accidental deployment of the airbag system.
- Inspect the wiring harness and connectors for any signs of damage, corrosion, or loose connections. Repair or replace as necessary.
- Check the front pretensioner squib for proper functionality. Replace if faulty.
- Clear the diagnostic trouble code from the vehicle's computer using a scan tool.
- Reconnect the battery and test the pretensioner system to ensure proper operation.
Cost to Fix B1908 2016 Toyota RAV4
The cost of repairing a short to positive in the front pretensioner squib left circuit can vary depending on the extent of the damage and the specific components that need to be replaced. In general, the parts required for this repair, such as a new front pretensioner squib or wiring harness, can range from $100 to $300. Labor costs at an auto repair shop typically range from $100 to $300 per hour, with the total repair time depending on the complexity of the issue. Therefore, the total repair cost for addressing the B1908 code can range from $200 to $600 or more. It's recommended to consult with a professional mechanic to get a more accurate estimate based on your specific vehicle and location.
Need more information about the B1908 2016 Toyota RAV4 code?
Need more information on how to fix the B1908 2016 Toyota RAV4 code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the B1908 2016 Toyota RAV4 code diagnosed by a professional: Find a repair shop in your area
Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service
- Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
- Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
- Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
- Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.
Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.
Frequently Asked Questions about B1908 2016 Toyota RAV4 Code
1. What does the OBDII code B1908 mean on a 2016 Toyota RAV4?
Code B1908 indicates a "Short to Positive in Front Pretensioner Squib Left Circuit," which means there is an electrical fault in the wiring or components related to the driver's side seat belt pretensioner.
2. What are the common symptoms of code B1908 in a Toyota RAV4?
Common symptoms include the airbag warning light staying illuminated on the dashboard and potential issues with the seat belt pretensioner not functioning properly during a collision.
3. What causes the B1908 code in a 2016 Toyota RAV4?
Causes can include damaged or shorted wiring, a faulty seat belt pretensioner, a defective airbag control module, or poor electrical connections in the circuit.
4. Is it safe to drive with a B1908 code in my Toyota RAV4?
It is not recommended to drive without addressing the issue, as it may affect the proper deployment of the airbag system and seat belt pretensioner in the event of an accident.
5. How can I diagnose the B1908 code on my Toyota RAV4?
Use an OBDII scanner to confirm the code, then inspect the wiring, connectors, and components in the left front pretensioner squib circuit for damage or shorts to positive voltage.
6. Can a blown fuse cause the B1908 code in my Toyota RAV4?
While a blown fuse is not a typical cause of this specific code, it is worth checking the airbag system fuses as part of the diagnostic process.
7. How do I fix the B1908 code on a 2016 Toyota RAV4?
Repairs may include replacing damaged wiring, repairing or replacing the seat belt pretensioner, or addressing issues with the airbag control module. Ensure all connectors are secure and free of corrosion.
8. Do I need to reset the airbag system after fixing the B1908 code?
Yes, after repairs are completed, you’ll need to use an OBDII scanner to clear the code and reset the airbag system.
9. What tools are needed to repair the B1908 code on a Toyota RAV4?
You’ll need an OBDII scanner, a multimeter to test for shorts or continuity, and possibly basic tools to access and inspect wiring and connectors.
10. Can a dealership repair the B1908 code on my Toyota RAV4?
Yes, a dealership has the specialized equipment and expertise to diagnose and repair airbag system issues like the B1908 code.
Discuss the causes and fixes for B1908 2016 Toyota RAV4 OBDII Code
Code B1908 2016 Toyota RAV4 comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.