B1906 Scion Code - Open in Front Pretensioner Squib Left Circuit
Quick Answer
The B1906 Scion code indicates an open circuit in the front pretensioner squib left circuit. Common causes include Loose or damaged wiring in the front pretensioner squib left circuit, Faulty pretensioner squib component, Corrosion or debris in the electrical connectors. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- B1906 Scion indicates Open in Front Pretensioner Squib Left Circuit.
- Common causes
- Common causes include Loose or damaged wiring in the front pretensioner squib left circuit, Faulty pretensioner squib component, Corrosion or debris in the electrical connectors.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
Code B1906 Scion Description
The B1906 Scion code indicates an open circuit in the front pretensioner squib left circuit. In simpler terms, this means that there is a problem with the wiring or connection in the left front seatbelt pretensioner system. The pretensioner squib is a component that is responsible for tightening the seatbelt in the event of a collision, helping to restrain the occupants and reduce the risk of injury.
Common Causes of B1906 Scion
- Loose or damaged wiring in the front pretensioner squib left circuit.
- Faulty pretensioner squib component.
- Corrosion or debris in the electrical connectors.
- Impact or collision that damaged the pretensioner system.
- Faulty airbag control module.
Symptoms of B1906 Scion
- Airbag warning light is illuminated on the dashboard.
- Seatbelt warning light may be illuminated.
- Seatbelt may not retract properly.
- The seatbelt may not tighten during sudden braking or a collision.
- Vehicle may fail an airbag system diagnostic test.
How to Fix B1906 Scion
- Start by diagnosing the specific cause of the open circuit, using a scan tool to read the fault codes and pinpoint the issue.
- Inspect the wiring and connectors in the front pretensioner squib left circuit for any damage, corrosion, or loose connections. Repair or replace as necessary.
- Test the pretensioner squib component to ensure it is functioning correctly. Replace if faulty.
- Clear the fault codes and reset the airbag system.
- Perform a test drive to verify that the issue has been resolved and that the airbag warning light is no longer illuminated.
Cost to Fix B1906 Scion
The cost of repairing an open circuit in the front pretensioner squib left circuit can vary depending on the specific cause of the issue and the labor rates in your area. On average, you can expect to pay between $150 to $400 for parts and labor. However, it's important to note that diagnostic time and labor rates can vary, so it's advisable to check with local auto repair shops for a more accurate estimate. Additionally, if the issue is more complex or requires the replacement of expensive components, the cost may be higher.
Need more information about the B1906 Scion code?
Need more information on how to fix the B1906 Scion code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the B1906 Scion code diagnosed by a professional: Find a repair shop in your area
Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service
- Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
- Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
- Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
- Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.
Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.
Frequently Asked Questions about B1906 Scion Code
1. What does OBDII code B1906 for Scion mean?
The code B1906 indicates an "Open in Front Pretensioner Squib Left Circuit" in a Scion vehicle.
2. What are the common symptoms of OBDII code B1906 in a Scion?
Common symptoms may include the airbag warning light staying illuminated on the dashboard and potential issues with the vehicle's airbag system.
3. What are the possible causes of OBDII code B1906 in a Scion?
Possible causes of code B1906 include a faulty pretensioner squib in the left front seatbelt, damaged wiring or connectors in the circuit, or a malfunctioning airbag control module.
4. How can I diagnose OBDII code B1906 in my Scion?
Diagnosing code B1906 typically involves using a scan tool to retrieve the code, inspecting the wiring and connectors related to the left front pretensioner squib, and testing the components for proper functionality.
5. Can I still drive my Scion with OBDII code B1906 present?
It is not recommended to drive the vehicle with an unresolved B1906 code, as it may indicate a potential issue with the airbag system, which is crucial for occupant safety in the event of a collision.
6. How can I repair OBDII code B1906 in my Scion?
Repairing code B1906 may involve replacing the faulty pretensioner squib, repairing or replacing damaged wiring or connectors, or resetting the airbag control module after addressing the underlying issue.
7. Is it safe to reset the OBDII code B1906 in my Scion without fixing the problem?
Resetting the code without addressing the underlying issue is not recommended, as it may lead to the airbag system not functioning properly in the event of an accident.
8. Can a DIY enthusiast fix OBDII code B1906 in a Scion?
While some DIY enthusiasts may have the skills to diagnose and repair code B1906, it is recommended to consult a professional mechanic or technician for proper diagnosis and repair to ensure the airbag system's safety and functionality.
9. How much does it cost to fix OBDII code B1906 in a Scion?
The cost of fixing code B1906 can vary depending on the underlying issue, such as replacing components, repairing wiring, or resetting the airbag control module. It is advisable to obtain a diagnosis and repair estimate from a qualified mechanic.
10. How important is it to address OBDII code B1906 promptly in a Scion?
It is crucial to address code B1906 promptly in a Scion to ensure the proper functioning of the airbag system, which plays a vital role in protecting occupants in the event of a collision. Delaying repairs may compromise vehicle safety.
Discuss the causes and fixes for B1906 Scion OBDII Code
Code B1906 Scion comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.