B1902 2017 Toyota RAV4 Code - Short to Ground in Front Pretensioner Squib Right Circuit
Quick Answer
The B1902 diagnostic trouble code for a 2017 Toyota RAV4 indicates a "Short to Ground in Front Pretensioner Squib Right Circuit." This code specifically points to an issue with the front pretensioner squib on the right side of the vehicle. Common causes include Wiring damage or corrosion in the front pretensioner squib right circuit, Faulty pretensioner squib component, Poor electrical connections in the circuit. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- B1902 2017 Toyota RAV4 indicates Short to Ground in Front Pretensioner Squib Right Circuit.
- Common causes
- Common causes include Wiring damage or corrosion in the front pretensioner squib right circuit, Faulty pretensioner squib component, Poor electrical connections in the circuit.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
Code B1902 2017 Toyota RAV4 Description
The B1902 diagnostic trouble code for a 2017 Toyota RAV4 indicates a "Short to Ground in Front Pretensioner Squib Right Circuit." This code specifically points to an issue with the front pretensioner squib on the right side of the vehicle. The pretensioner squib is a component of the seatbelt system that helps to tighten the seatbelt in the event of a collision, providing additional protection for the occupants.
Common Causes of B1902 2017 Toyota RAV4
- Wiring damage or corrosion in the front pretensioner squib right circuit.
- Faulty pretensioner squib component.
- Poor electrical connections in the circuit.
- Impact or collision that damaged the seatbelt system.
- Manufacturing defect in the pretensioner squib.
Symptoms of B1902 2017 Toyota RAV4
- Illumination of the airbag warning light on the dashboard.
- Inability to properly tighten the seatbelt during sudden stops or collisions.
- Erratic deployment of the pretensioner squib during normal driving conditions.
- Diagnostic trouble codes related to the airbag system stored in the vehicle's computer.
How to Fix B1902 2017 Toyota RAV4
- Begin by disconnecting the vehicle's battery to prevent any electrical mishaps during the repair process.
- Inspect the wiring and connections in the front pretensioner squib right circuit for any signs of damage, corrosion, or loose connections.
- Test the pretensioner squib component to determine if it is functioning correctly or needs to be replaced.
- Repair or replace any damaged wiring, connectors, or the pretensioner squib as necessary.
- Clear the diagnostic trouble codes from the vehicle's computer and perform a test to ensure that the issue has been resolved.
Cost to Fix B1902 2017 Toyota RAV4
The typical repair costs for addressing a short to ground in the front pretensioner squib right circuit on a 2017 Toyota RAV4 can range from $200 to $500, including parts and labor. However, it is important to note that the specific diagnosis time and labor rates at auto repair shops can vary based on factors such as location, vehicle make and model, and engine type. Auto repair shops commonly charge between $80 and $150 per hour for labor, with rates potentially higher in metropolitan areas or at dealerships, and lower at independent shops. It is recommended to obtain local estimates for a more accurate cost assessment.
Need more information about the B1902 2017 Toyota RAV4 code?
Need more information on how to fix the B1902 2017 Toyota RAV4 code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the B1902 2017 Toyota RAV4 code diagnosed by a professional: Find a repair shop in your area
Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service
- Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
- Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
- Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
- Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.
Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.
Frequently Asked Questions about B1902 2017 Toyota RAV4 Code
1. What does the OBDII code B1902 mean on a 2017 Toyota RAV4?
The code B1902 indicates a short to ground in the front passenger-side pretensioner squib circuit, which is part of the airbag system.
2. What are the common symptoms of code B1902 in a 2017 Toyota RAV4?
The most common symptoms include the airbag warning light staying illuminated and the possibility of the passenger seatbelt pretensioner not functioning correctly in a collision.
3. What causes the B1902 code to be triggered in a 2017 Toyota RAV4?
This code is typically caused by damaged wiring, a short to ground in the circuit, a faulty seatbelt pretensioner, or a defective airbag control module.
4. Can I drive my 2017 Toyota RAV4 with the B1902 code active?
While the vehicle may still be drivable, it is unsafe as the airbag system may not deploy or function properly in the event of a collision.
5. How do I diagnose the B1902 code on a 2017 Toyota RAV4?
Diagnose the issue by checking the wiring and connectors for the front passenger pretensioner squib, testing for shorts to ground, and using a scan tool to monitor the airbag system.
6. What repairs are needed to fix the B1902 code in a 2017 Toyota RAV4?
Repairs may include fixing or replacing damaged wiring, connectors, or the seatbelt pretensioner, or, in some cases, replacing the airbag control module.
7. How much does it typically cost to repair the B1902 code on a 2017 Toyota RAV4?
Repair costs can vary widely but typically range from $100 to $500 or more, depending on whether wiring repairs or component replacements are necessary.
8. Can I fix the B1902 code on my 2017 Toyota RAV4 myself?
If you have experience with automotive electrical systems, you might be able to inspect and repair wiring issues. However, due to the complexity of the airbag system, professional assistance is often recommended.
9. Does clearing the B1902 code fix the problem on a 2017 Toyota RAV4?
Clearing the code will reset the warning light temporarily, but the issue will persist unless the underlying problem is resolved.
10. What tools are needed to troubleshoot the B1902 code on a 2017 Toyota RAV4?
You’ll need a scan tool capable of reading airbag system codes, a multimeter for testing electrical circuits, and possibly a wiring diagram for the pretensioner circuit.
Discuss the causes and fixes for B1902 2017 Toyota RAV4 OBDII Code
Code B1902 2017 Toyota RAV4 comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.