B1902 2014 Toyota RAV4 Code - Short to Ground in Front Pretensioner Squib Right Circuit
Quick Answer
The B1902 diagnostic trouble code for a 2014 Toyota RAV4 indicates a "Short to Ground in Front Pretensioner Squib Right Circuit." This code is related to the vehicle's front seat belt pretensioner system, specifically the right side. Common causes include Damaged wiring or connectors in the front pretensioner squib right circuit, Faulty pretensioner squib, Malfunctioning airbag control module. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- B1902 2014 Toyota RAV4 indicates Short to Ground in Front Pretensioner Squib Right Circuit.
- Common causes
- Common causes include Damaged wiring or connectors in the front pretensioner squib right circuit, Faulty pretensioner squib, Malfunctioning airbag control module.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
Code B1902 2014 Toyota RAV4 Description
The B1902 diagnostic trouble code for a 2014 Toyota RAV4 indicates a "Short to Ground in Front Pretensioner Squib Right Circuit." This code is related to the vehicle's front seat belt pretensioner system, specifically the right side. The pretensioner system is designed to retract the seat belt in the event of a collision, reducing the slack to securely hold the occupant in place and minimize injury.
Common Causes of B1902 2014 Toyota RAV4
- Damaged wiring or connectors in the front pretensioner squib right circuit
- Faulty pretensioner squib
- Malfunctioning airbag control module
- Poor electrical connections
- Vehicle collision or impact causing damage to the system
Symptoms of B1902 2014 Toyota RAV4
- Illumination of the airbag warning light on the dashboard
- Inoperative front seat belt pretensioner on the right side
- Fault code stored in the vehicle's computer system
- Potential loss of safety functionality in the event of a collision
How to Fix B1902 2014 Toyota RAV4
- Begin by diagnosing the specific cause of the short to ground in the front pretensioner squib right circuit, using a diagnostic scanner and multimeter to test the circuit and components.
- Inspect the wiring and connectors in the circuit for any damage, corrosion, or loose connections. Repair or replace as necessary.
- Test the front pretensioner squib on the right side to determine if it is faulty. Replace if needed.
- Check the airbag control module for any malfunctions or faults. Reset or replace as required.
- Clear the fault codes from the vehicle's computer system and perform a test drive to ensure the issue has been resolved.
Cost to Fix B1902 2014 Toyota RAV4
The typical repair costs for addressing a B1902 code in a 2014 Toyota RAV4 can vary depending on the specific cause of the issue. On average, the cost of parts for this repair can range from $100 to $500, with labor costs adding an additional $100 to $200. However, it's important to note that diagnosis time and labor rates at auto repair shops can vary based on location, vehicle make and model, and engine type. It is recommended to check with local repair shops for a more accurate estimate.
Need more information about the B1902 2014 Toyota RAV4 code?
Need more information on how to fix the B1902 2014 Toyota RAV4 code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the B1902 2014 Toyota RAV4 code diagnosed by a professional: Find a repair shop in your area
Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service
- Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
- Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
- Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
- Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.
Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.
Frequently Asked Questions about B1902 2014 Toyota RAV4 Code
1. What does OBDII code B1902 mean for a 2014 Toyota RAV4?
The code B1902 indicates a "Short to Ground in Front Pretensioner Squib Right Circuit" in the vehicle's airbag system.
2. What are the common symptoms of OBDII code B1902 in a 2014 Toyota RAV4?
Common symptoms may include the airbag warning light being illuminated on the dashboard and potentially a non-functioning airbag system.
3. What are the possible causes of OBDII code B1902 in a 2014 Toyota RAV4?
Possible causes of this code include damaged wiring in the front pretensioner squib right circuit, a faulty pretensioner squib, or a malfunctioning airbag control module.
4. How can I diagnose the issue related to OBDII code B1902 in my 2014 Toyota RAV4?
Diagnosing the issue may require using a diagnostic scanner to retrieve the specific fault codes, inspecting the wiring and connections in the front pretensioner squib right circuit, and testing the components for proper functionality.
5. Can I drive my 2014 Toyota RAV4 with OBDII code B1902 present?
It is not recommended to drive the vehicle with an active airbag system fault code like B1902, as it may compromise the safety features of the vehicle in the event of a collision.
6. How can I repair OBDII code B1902 in my 2014 Toyota RAV4?
Repairing this code may involve repairing or replacing damaged wiring, replacing the pretensioner squib if faulty, or addressing any issues with the airbag control module.
7. Is it safe to reset the OBDII code B1902 in a 2014 Toyota RAV4 without fixing the underlying issue?
Resetting the code without addressing the root cause is not recommended, as the safety of the airbag system could still be compromised. It's important to diagnose and repair the issue properly.
8. Can a DIY enthusiast fix OBDII code B1902 in a 2014 Toyota RAV4?
While some basic diagnostic steps can be performed by a DIY enthusiast, dealing with airbag system issues like B1902 may require specialized knowledge and tools, so it's advisable to consult a professional.
9. How much does it typically cost to repair OBDII code B1902 in a 2014 Toyota RAV4?
The cost of repairing this code can vary depending on the extent of the damage and the specific components that need to be repaired or replaced. It's recommended to obtain quotes from automotive professionals.
10. Are there any recalls or service bulletins related to OBDII code B1902 for the 2014 Toyota RAV4?
It's advisable to check with Toyota dealership or visit the NHTSA website to see if there are any recalls or service bulletins related to OBDII code B1902 specific to your vehicle.
Discuss the causes and fixes for B1902 2014 Toyota RAV4 OBDII Code
Code B1902 2014 Toyota RAV4 comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.