B1902 2013 Toyota RAV4 Code - Short to Ground in Front Pretensioner Squib Right Circuit
Quick Answer
The B1902 diagnostic trouble code (DTC) for a 2013 Toyota RAV4 indicates a "Short to Ground in Front Pretensioner Squib Right Circuit." This code specifically refers to an issue with the front pretensioner squib circuit on the right side of the vehicle. Common causes include Wiring damage or short circuits in the front pretensioner squib circuit, Faulty connectors or poor electrical connections, Malfunctioning front pretensioner squib. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- B1902 2013 Toyota RAV4 indicates Short to Ground in Front Pretensioner Squib Right Circuit.
- Common causes
- Common causes include Wiring damage or short circuits in the front pretensioner squib circuit, Faulty connectors or poor electrical connections, Malfunctioning front pretensioner squib.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
Code B1902 2013 Toyota RAV4 Description
The B1902 diagnostic trouble code (DTC) for a 2013 Toyota RAV4 indicates a "Short to Ground in Front Pretensioner Squib Right Circuit." This code specifically refers to an issue with the front pretensioner squib circuit on the right side of the vehicle. The pretensioner squib is a crucial component of the vehicle's safety system, specifically designed to tighten the seatbelt in the event of a collision, reducing the risk of injury to the occupants.
Common Causes of B1902 2013 Toyota RAV4
- Wiring damage or short circuits in the front pretensioner squib circuit.
- Faulty connectors or poor electrical connections.
- Malfunctioning front pretensioner squib.
- Issues with the airbag control module.
- Vehicle collision or impact that may have damaged the pretensioner system.
Symptoms of B1902 2013 Toyota RAV4
- Illumination of the airbag warning light on the dashboard.
- Inability to properly tighten the seatbelt during sudden braking or collision.
- Diagnostic trouble code B1902 stored in the vehicle's computer system.
- Failed safety inspections due to malfunctioning seatbelt system.
How to Fix B1902 2013 Toyota RAV4
- Begin by disconnecting the vehicle's battery to prevent accidental deployment of the airbag system.
- Inspect the wiring, connectors, and pretensioner squib for any signs of damage or wear.
- Test the electrical components using a multimeter to identify the specific location of the short to ground.
- Replace any damaged wiring, connectors, or the pretensioner squib as needed.
- Clear the diagnostic trouble code from the vehicle's computer system and perform a test to ensure the issue has been resolved.
Cost to Fix B1902 2013 Toyota RAV4
The typical repair costs for addressing a B1902 code in a 2013 Toyota RAV4 can vary depending on the specific cause of the issue. In general, the cost of parts such as wiring, connectors, or a new pretensioner squib can range from $200 to $500. Labor costs for the repair process can add an additional $150 to $300, depending on the shop's hourly rates and the complexity of the repair.
Need more information about the B1902 2013 Toyota RAV4 code?
Need more information on how to fix the B1902 2013 Toyota RAV4 code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the B1902 2013 Toyota RAV4 code diagnosed by a professional: Find a repair shop in your area
Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service
- Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
- Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
- Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
- Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.
Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.
Frequently Asked Questions about B1902 2013 Toyota RAV4 Code
1. What are the common symptoms of OBDII code B1902 in a 2013 Toyota RAV4?
The common symptoms include the airbag warning light illuminating on the dashboard and possible non-deployment of the seatbelt pretensioner in the event of a collision.
2. What does the OBDII code B1902 "Short to Ground in Front Pretensioner Squib Right Circuit" mean in a 2013 Toyota RAV4?
This code indicates a potential electrical issue in the front pretensioner squib circuit on the right side, specifically a short to ground.
3. What are possible causes of OBDII code B1902 in a 2013 Toyota RAV4?
Potential causes include damaged wiring or connectors in the front pretensioner squib circuit, a faulty pretensioner squib, or a problem with the airbag control module.
4. How can I diagnose the OBDII code B1902 in my 2013 Toyota RAV4?
Diagnosing this code typically involves inspecting the wiring and connectors in the front pretensioner squib circuit, testing the pretensioner squib resistance, and checking for any faults in the airbag control module.
5. Can I drive my 2013 Toyota RAV4 with OBDII code B1902?
It is not recommended to drive the vehicle with this code present, as it may affect the proper functioning of the seatbelt pretensioner in the event of a collision.
6. How can I repair OBDII code B1902 in my 2013 Toyota RAV4?
Repairing this code may involve repairing or replacing damaged wiring or connectors, replacing the pretensioner squib if faulty, or addressing any issues with the airbag control module.
7. Is it safe to reset the OBDII code B1902 in my 2013 Toyota RAV4 without fixing the underlying issue?
Resetting the code without addressing the underlying problem may temporarily turn off the warning light but will not fix the potential safety issue with the seatbelt pretensioner system.
8. Can a DIY enthusiast fix OBDII code B1902 in a 2013 Toyota RAV4?
While diagnosing and repairing this code may require advanced knowledge and specialized tools, experienced DIY enthusiasts with proper guidance can attempt to fix it.
9. How much does it cost to repair OBDII code B1902 in a 2013 Toyota RAV4 at a mechanic?
The cost of repairing this code can vary depending on the underlying issue, with potential costs including labor charges, replacement parts, and diagnostic fees.
10. How often does OBDII code B1902 occur in a 2013 Toyota RAV4?
The occurrence of this code can vary, but it is relatively uncommon compared to other OBDII codes in the 2013 Toyota RAV4 related to the airbag system.
Discuss the causes and fixes for B1902 2013 Toyota RAV4 OBDII Code
Code B1902 2013 Toyota RAV4 comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.