B1860 2018 Toyota RAV4 Code - Short in Driver Side Knee Airbag Squib Circuit
Quick Answer
The B1860 diagnostic trouble code (DTC) for a 2018 Toyota RAV4 indicates a short in the driver side knee airbag squib circuit. Common causes include Damaged wiring in the driver side knee airbag squib circuit, Faulty connectors or poor connections in the circuit, Malfunctioning driver side knee airbag squib. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- B1860 2018 Toyota RAV4 indicates Short in Driver Side Knee Airbag Squib Circuit.
- Common causes
- Common causes include Damaged wiring in the driver side knee airbag squib circuit, Faulty connectors or poor connections in the circuit, Malfunctioning driver side knee airbag squib.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
Code B1860 2018 Toyota RAV4 Description
The B1860 diagnostic trouble code (DTC) for a 2018 Toyota RAV4 indicates a short in the driver side knee airbag squib circuit. This means that there is an electrical issue in the circuit responsible for deploying the driver side knee airbag. The knee airbag is an important safety feature designed to provide additional protection to the driver's lower body in the event of a collision. A short in this circuit can prevent the airbag from deploying properly or at all, compromising the vehicle's occupant protection system.
Common Causes of B1860 2018 Toyota RAV4
- Damaged wiring in the driver side knee airbag squib circuit.
- Faulty connectors or poor connections in the circuit.
- Malfunctioning driver side knee airbag squib.
- Water or moisture intrusion affecting the circuit.
- Previous collision or impact that damaged the airbag system components.
Symptoms of B1860 2018 Toyota RAV4
- Airbag warning light illuminated on the dashboard.
- Inability to deploy the driver side knee airbag in a collision.
- Fault codes related to the driver side knee airbag squib circuit in the vehicle's computer system.
- Loss of communication with the airbag control module.
How to Fix B1860 2018 Toyota RAV4
- Begin by diagnosing the specific cause of the short in the driver side knee airbag squib circuit using a diagnostic scan tool.
- Inspect the wiring and connectors in the circuit for any signs of damage or corrosion. Repair or replace any damaged components.
- Test the driver side knee airbag squib to determine if it is functioning correctly. Replace the squib if necessary.
- Clear the DTC from the vehicle's computer system and perform a test to ensure the airbag warning light is no longer illuminated.
- Conduct a thorough system check to verify that the driver side knee airbag system is operating as intended.
Cost to Fix B1860 2018 Toyota RAV4
The cost of repairing a short in the driver side knee airbag squib circuit can vary depending on the extent of the damage and the specific components that need to be replaced. In general, the parts required for this repair, such as wiring, connectors, and the squib itself, can range from $200 to $500. Labor costs typically add an additional $100 to $300, bringing the total repair cost to approximately $300 to $800.
Need more information about the B1860 2018 Toyota RAV4 code?
Need more information on how to fix the B1860 2018 Toyota RAV4 code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the B1860 2018 Toyota RAV4 code diagnosed by a professional: Find a repair shop in your area
Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service
- Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
- Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
- Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
- Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.
Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.
Frequently Asked Questions about B1860 2018 Toyota RAV4 Code
1. What does the OBDII code B1860 mean on a 2018 Toyota RAV4?
The code B1860 indicates a short circuit in the driver-side knee airbag squib circuit, which is part of the Supplemental Restraint System (SRS).
2. What are the common symptoms of code B1860 in a 2018 Toyota RAV4?
Symptoms include the airbag warning light staying illuminated and potential deactivation of the driver-side knee airbag.
3. What causes the B1860 code to appear?
Common causes include damaged or shorted wiring, a faulty driver-side knee airbag squib, a malfunctioning clock spring, or a defective SRS control module.
4. Is it safe to drive with the B1860 code active?
No, it is not safe because the airbag system may not deploy properly in an accident, compromising safety.
5. How is the B1860 code diagnosed?
Technicians diagnose this code by using an OBDII scanner, inspecting the airbag system wiring, checking the clock spring, and testing the knee airbag squib for shorts or damage.
6. Can I reset the B1860 code without repairs?
Clearing the code without addressing the underlying issue is not recommended, as the airbag system will remain compromised.
7. How do you fix the B1860 code on a 2018 Toyota RAV4?
Repairs may involve replacing damaged wiring, repairing the clock spring, or replacing the driver-side knee airbag squib or SRS control module.
8. How much does it cost to repair the B1860 code?
Repair costs vary depending on the issue but can range from $100 for wiring repairs to over $1,000 for component replacements like the airbag squib or SRS control module.
9. Can a faulty clock spring cause the B1860 code?
Yes, a faulty clock spring can disrupt the electrical connection to the airbag squib, triggering the B1860 code.
10. Do I need professional help to fix the B1860 code?
Yes, due to the complexity and safety-critical nature of the airbag system, it is recommended to have a certified technician handle the repairs.
Discuss the causes and fixes for B1860 2018 Toyota RAV4 OBDII Code
Code B1860 2018 Toyota RAV4 comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.