B1806 2018 Toyota RAV4 Code - Open In Front Passenger Side Squib Circuit
Quick Answer
The B1806 diagnostic trouble code (DTC) for a 2018 Toyota RAV4 indicates an open circuit in the front passenger side squib circuit. Common causes include Loose or corroded electrical connections in the front passenger side squib circuit, Damage to the wiring harness that connects the front passenger side airbag to the SRS control module, Faulty front passenger side airbag squib. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- B1806 2018 Toyota RAV4 indicates Open In Front Passenger Side Squib Circuit.
- Common causes
- Common causes include Loose or corroded electrical connections in the front passenger side squib circuit, Damage to the wiring harness that connects the front passenger side airbag to the SRS control module, Faulty front passenger side airbag squib.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
Code B1806 2018 Toyota RAV4 Description
The B1806 diagnostic trouble code (DTC) for a 2018 Toyota RAV4 indicates an open circuit in the front passenger side squib circuit. The squib circuit is a part of the vehicle's supplemental restraint system (SRS), commonly known as the airbag system. When this code is triggered, it means that there is a break or discontinuity in the electrical circuit that connects the front passenger side airbag to the vehicle's SRS control module.
Common Causes of B1806 2018 Toyota RAV4
- Loose or corroded electrical connections in the front passenger side squib circuit.
- Damage to the wiring harness that connects the front passenger side airbag to the SRS control module.
- Faulty front passenger side airbag squib.
- Issues with the SRS control module itself.
- Previous collision or impact that damaged the airbag system components.
Symptoms of B1806 2018 Toyota RAV4
- Illumination of the airbag warning light on the dashboard.
- Front passenger side airbag may not deploy in a collision.
- Audible chime or warning message indicating an issue with the airbag system.
- Diagnostic trouble code B1806 stored in the vehicle's onboard computer.
How to Fix B1806 2018 Toyota RAV4
- Begin by disconnecting the vehicle's battery to prevent accidental deployment of the airbag system.
- Inspect the wiring harness and connectors in the front passenger side squib circuit for any signs of damage, corrosion, or looseness. Repair or replace any damaged components.
- Check the front passenger side airbag squib for continuity using a multimeter. Replace the squib if it is faulty.
- Clear the diagnostic trouble code from the vehicle's onboard computer using a scan tool.
- Reconnect the battery and test the airbag system to ensure proper functionality.
Cost to Fix B1806 2018 Toyota RAV4
The cost of repairing an open circuit in the front passenger side squib circuit can vary depending on the extent of the damage and the specific components that need to be replaced. In general, the cost of parts for this repair can range from $200 to $500, while labor costs can range from $100 to $300. This brings the total estimated cost of repairing the B1806 code to approximately $300 to $800. It's important to note that these are rough estimates, and actual costs may vary based on factors such as location, labor rates, and the availability of parts. It's recommended to consult with a qualified mechanic or auto repair shop for a more accurate cost estimate tailored to your specific vehicle and situation.
Need more information about the B1806 2018 Toyota RAV4 code?
Need more information on how to fix the B1806 2018 Toyota RAV4 code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the B1806 2018 Toyota RAV4 code diagnosed by a professional: Find a repair shop in your area
Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service
- Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
- Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
- Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
- Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.
Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.
Frequently Asked Questions about B1806 2018 Toyota RAV4 Code
What does OBDII code B1806 mean for a 2018 Toyota RAV4?
OBDII code B1806 indicates an open circuit in the front passenger side squib, which is related to the airbag system. This means there is a fault in the wiring or components that affects the airbag deployment.
What are the common symptoms associated with code B1806?
Common symptoms include the airbag warning light illuminating on the dashboard, malfunctioning passenger-side airbags, and potentially a disabled airbag system for the front passenger seat.
What could cause the B1806 code to trigger?
Causes may include a damaged or disconnected wiring harness, faulty airbag module, issues with the passenger seat occupancy sensor, or a problem with the airbag itself.
How can I diagnose the issue related to code B1806?
To diagnose the issue, check the wiring and connectors for damage or corrosion, use an OBDII scanner to read any additional codes, and perform a visual inspection of the airbag system components related to the front passenger side.
Can I drive my 2018 Toyota RAV4 with code B1806?
It is not recommended to drive the vehicle with code B1806 present, as the airbag system may not function properly in the event of a collision, posing a safety risk.
What are some repair options for code B1806?
Repair options include repairing or replacing damaged wiring, replacing a faulty airbag module, or addressing issues with the seat occupancy sensor. It's best to have these repairs performed by a qualified technician.
Is it safe to clear the B1806 code without fixing the issue?
No, clearing the code without addressing the underlying problem is not safe, as the airbag system may still be compromised, leaving you and your passengers unprotected in an accident.
How much does it typically cost to fix the issues related to code B1806?
Repair costs can vary widely depending on the specific issue, but it can range from $100 to over $1,000 if major components like the airbag module need replacement.
Do I need special tools to troubleshoot code B1806?
Yes, you will need an OBDII scanner to read and clear codes, and possibly a multimeter to check electrical connections and continuity in the squib circuit.
Discuss the causes and fixes for B1806 2018 Toyota RAV4 OBDII Code
Code B1806 2018 Toyota RAV4 comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.