B1642 2018 Toyota RAV4 Code - Lost Communication With Side Satellite Sensor Bus Right
Quick Answer
The B1642 diagnostic trouble code for a 2018 Toyota RAV4 indicates that there is a communication issue with the Side Satellite Sensor Bus on the right side of the vehicle. Common causes include Damaged wiring or connectors in the side satellite sensor bus circuit, Faulty sensor on the right side of the vehicle, Malfunctioning control module managing communication on the bus. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- B1642 2018 Toyota RAV4 indicates Lost Communication With Side Satellite Sensor Bus Right.
- Common causes
- Common causes include Damaged wiring or connectors in the side satellite sensor bus circuit, Faulty sensor on the right side of the vehicle, Malfunctioning control module managing communication on the bus.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
Code B1642 2018 Toyota RAV4 Description
The B1642 diagnostic trouble code for a 2018 Toyota RAV4 indicates that there is a communication issue with the Side Satellite Sensor Bus on the right side of the vehicle. This sensor bus is responsible for transmitting data between various sensors located on the right side of the vehicle, such as the side airbags, blind spot monitoring system, and other safety features. When communication is lost with this bus, it can lead to a variety of safety systems not functioning properly, potentially putting the driver and passengers at risk.
Common Causes of B1642 2018 Toyota RAV4
- Damaged wiring or connectors in the side satellite sensor bus circuit
- Faulty sensor on the right side of the vehicle
- Malfunctioning control module managing communication on the bus
- Water damage or corrosion affecting the sensors on the right side
- Electrical interference from aftermarket accessories or modifications
Symptoms of B1642 2018 Toyota RAV4
- Airbag warning light illuminated on the dashboard
- Blind spot monitoring system not working
- Stability control or traction control warning lights activated
- Side airbags not deploying in a side impact collision
How to Fix B1642 2018 Toyota RAV4
- Perform a thorough inspection of the side satellite sensor bus wiring and connectors for any damage or corrosion.
- Test the sensors on the right side of the vehicle to ensure they are functioning correctly.
- Check the control module responsible for managing communication on the bus for any faults.
- Clear the diagnostic trouble code from the vehicle's system and test the affected safety features to ensure they are working properly.
- If necessary, replace any damaged wiring, connectors, sensors, or control modules to resolve the communication issue.
Cost to Fix B1642 2018 Toyota RAV4
The typical repair costs for addressing a lost communication issue with the side satellite sensor bus on a 2018 Toyota RAV4 can vary depending on the exact cause of the problem. In general, parts and labor for this type of repair could range from $200 to $800. However, it's important to note that specific diagnosis time and labor rates at auto repair shops can vary based on factors such as location, vehicle make and model, and engine type. Most auto repair shops commonly charge between $80 and $150 per hour for labor. Rates may be higher at dealerships or in metropolitan areas, while independent shops often charge less. It's advisable to check local rates for a more precise estimate.
Need more information about the B1642 2018 Toyota RAV4 code?
Need more information on how to fix the B1642 2018 Toyota RAV4 code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the B1642 2018 Toyota RAV4 code diagnosed by a professional: Find a repair shop in your area
Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service
- Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
- Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
- Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
- Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.
Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.
Frequently Asked Questions about B1642 2018 Toyota RAV4 Code
1. What are the common symptoms of OBDII code B1642 in a 2018 Toyota RAV4?
- Common symptoms include the airbag warning light coming on, loss of communication with the side satellite sensor on the right side of the vehicle, and possible issues with the airbag system.
2. What can cause the OBDII code B1642 in a 2018 Toyota RAV4?
- The code B1642 is typically triggered by a communication error between the airbag control module and the side satellite sensor on the right side of the vehicle. This can be caused by wiring issues, a faulty sensor, or a malfunction in the airbag control module.
3. How can I diagnose the OBDII code B1642 in my 2018 Toyota RAV4?
- Diagnosing this code usually involves checking the wiring connections between the airbag control module and the side satellite sensor, testing the sensor itself for proper function, and scanning the system for any other related trouble codes.
4. Can I drive my 2018 Toyota RAV4 with the OBDII code B1642?
- It's not recommended to drive the vehicle with the B1642 code present, as it indicates a potential issue with the airbag system. Driving with a faulty airbag system can compromise your safety in the event of a collision.
5. How can I repair the OBDII code B1642 in my 2018 Toyota RAV4?
- Repairing the B1642 code may involve fixing any wiring issues, replacing the side satellite sensor on the right side of the vehicle if necessary, or reprogramming the airbag control module to establish proper communication.
6. Is the OBDII code B1642 in a 2018 Toyota RAV4 a serious issue?
- Yes, the B1642 code is a serious issue as it relates to the airbag system. It's crucial to address this problem promptly to ensure the proper function of the airbags in case of an accident.
7. How much does it typically cost to fix the OBDII code B1642 in a 2018 Toyota RAV4?
- The cost of fixing the B1642 code can vary depending on the root cause of the issue. It may range from a simple wiring repair to a sensor replacement, so it's best to consult a professional for an accurate estimate.
8. Can I reset the OBDII code B1642 in my 2018 Toyota RAV4 on my own?
- While you can clear the code with an OBDII scanner, it's important to address the underlying issue causing the B1642 code to prevent it from recurring. Simply clearing the code without fixing the problem may lead to safety concerns.
9. Are there any recalls or service bulletins related to the OBDII code B1642 in a 2018 Toyota RAV4?
- It's advisable to check with a Toyota dealership or visit the National Highway Traffic Safety Administration (NHTSA) website to see if there are any recalls or service bulletins related to the B1642 code for the 2018 Toyota RAV4.
10. How long does it typically take to repair the OBDII code B1642 in a 2018 Toyota RAV4?
- The repair time for the B1642 code can vary based on the complexity of the issue. Simple fixes like wiring repairs may take less time, while replacing components or reprogramming modules could extend the repair duration.
Discuss the causes and fixes for B1642 2018 Toyota RAV4 OBDII Code
Code B1642 2018 Toyota RAV4 comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.