B1353 GMC Code - Passenger Front Airbag Resistance Too High
Quick Answer
The B1353 GMC code indicates that there is an issue with the passenger front airbag system in the vehicle. Common causes include Faulty passenger airbag sensor, Loose or corroded wiring connections in the airbag circuit, Defective airbag module. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- B1353 GMC indicates Passenger Front Airbag Resistance Too High.
- Common causes
- Common causes include Faulty passenger airbag sensor, Loose or corroded wiring connections in the airbag circuit, Defective airbag module.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
Code B1353 GMC Description
The B1353 GMC code indicates that there is an issue with the passenger front airbag system in the vehicle. Specifically, it means that the resistance in the passenger front airbag circuit is too high. This could potentially prevent the airbag from deploying properly in the event of a collision, putting the passenger at risk of injury.
Common Causes of B1353 GMC
- Faulty passenger airbag sensor.
- Loose or corroded wiring connections in the airbag circuit.
- Defective airbag module.
- Impact or damage to the airbag system components.
- Electrical issues within the airbag system.
Symptoms of B1353 GMC
- Airbag warning light illuminated on the dashboard.
- Passenger airbag may not deploy in a collision.
- Diagnostic trouble code (DTC) B1353 stored in the vehicle's computer system.
- Intermittent or erratic behavior of the airbag system.
- Loss of communication with the airbag system during diagnostic testing.
How to Fix B1353 GMC
- Begin by diagnosing the specific cause of the high resistance in the passenger front airbag circuit using a diagnostic scanner.
- Inspect the wiring and connections in the airbag circuit for any damage, corrosion, or loose connections. Repair or replace as necessary.
- Test the passenger airbag sensor for proper functionality and replace if faulty.
- Check the airbag module for any defects or malfunctions and replace if needed.
- Clear the diagnostic trouble code (DTC) from the vehicle's computer system and perform a test to ensure that the issue has been resolved.
Cost to Fix B1353 GMC
The cost of repairing a B1353 GMC code can vary depending on the specific cause of the issue and the extent of the repairs needed. On average, the repair costs for this type of airbag system issue can range from $200 to $600, including parts and labor. However, it is important to note that labor rates at auto repair shops can vary widely, typically ranging from $80 to $150 per hour. Additionally, the cost of parts and the specific diagnosis time can also impact the overall repair cost. It is recommended to obtain quotes from local auto repair shops to get a more accurate estimate for this repair.
Need more information about the B1353 GMC code?
Need more information on how to fix the B1353 GMC code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the B1353 GMC code diagnosed by a professional: Find a repair shop in your area
Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service
- Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
- Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
- Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
- Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.
Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.
Frequently Asked Questions about B1353 GMC Code
1. What are the common symptoms of OBDII code B1353 GMC (Passenger Front Airbag Resistance Too High)?
- The common symptoms include the airbag warning light illuminating on the dashboard and a message indicating an issue with the passenger front airbag system.
2. What are the possible causes of OBDII code B1353 GMC?
- Some possible causes of this code are a faulty passenger front airbag module, a loose connection in the airbag system, or issues with the wiring harness.
3. How can I diagnose the cause of OBDII code B1353 GMC?
- To diagnose the cause of this code, you can use a diagnostic scan tool to retrieve the specific trouble codes, inspect the wiring and connections in the passenger front airbag system, and test the resistance of the airbag module.
4. Is it safe to drive with OBDII code B1353 GMC active?
- It is not recommended to drive with this code active, as it indicates a potential issue with the passenger front airbag system, which can affect its functionality in the event of a collision.
5. How can I repair OBDII code B1353 GMC?
- Repairing this code may involve replacing the passenger front airbag module, repairing any damaged wiring or connections, and clearing the trouble codes with a diagnostic scan tool.
6. Can I reset OBDII code B1353 GMC without fixing the underlying issue?
- While you can clear the code temporarily with a scan tool, it is important to address the underlying issue causing the code to prevent potential safety risks in the event of an accident.
7. Are there any DIY tips for troubleshooting OBDII code B1353 GMC?
- DIY troubleshooting tips include checking for loose connections, inspecting the wiring harness for damage, and ensuring the airbag module is securely fastened in place.
8. How much does it typically cost to repair OBDII code B1353 GMC?
- The cost of repairing this code can vary depending on the specific cause, but it may involve parts and labor costs ranging from $100 to $500 or more, depending on the extent of the repairs needed.
9. Can a mechanic help me fix OBDII code B1353 GMC, or is it a DIY task?
- A mechanic with experience in airbag systems can help diagnose and repair OBDII code B1353 GMC, as it involves specialized knowledge and equipment to ensure proper repairs and safety.
10. How long does it take to repair OBDII code B1353 GMC?
- The repair time for this code can vary depending on the cause and complexity of the issue, but it may take anywhere from a few hours to a full day to diagnose and repair the problem effectively.
Discuss the causes and fixes for B1353 GMC OBDII Code
Code B1353 GMC comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.