Engine-Codes - Buick - B1155 Buick

B1155 Buick Code - SDM Calibration Mismatch

- Code Popularity: 398 Views
- Repair Importance Level: 3/3
- Repair Difficulty Level: 3/3
Table of contents
ChatAC AutoCodes.com AI Chat

What are the Possible Causes of the DTC B1155 Buick?

NOTE: The causes shown may not be a complete list of all potential problems, and it is possible that there may be other causes.
  • Faulty Sensing and Diagnostic Module (SDM)
  • Sensing and Diagnostic Module (SDM) harness is open or shorted
  • Sensing and Diagnostic Module (SDM) circuit poor electrical connection

Code Tech Notes

If DTCs B1155, B1159, and B1160 are all set, the Sensing and Diagnostic Module (SDM) is receiving both incorrect messages.
If DTCs B1155 and B1159 are set, SDM is receiving the wrong message from Standard Body Module (SBM).
If DTCs B1155 and B1160 are set, SDM is receiving the wrong message from Powertrain Control Module (PCM).
If DTC B1159 sets alone, SDM did not receive a message from SBM.
If DTC B1160 sets alone, SDM did not receive a message from PCM.
If DTCs B1159 and B1160 are set without DTC B1155, SDM did not receive messages from SBM or PCM.

⚠ Does your Buick have Safety Recalls? → Check here

How to Fix the DTC B1155 Buick?

Check the 'Possible Causes' listed above. Visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector pins.

Search for B1155 Buick Questions and Answers: Search here →

What is the Cost to Diagnose the Code?

Labor: 1.0

The cost to diagnose the B1155 Buick code is 1.0 hour of labor. The diagnosis time and labor rates at auto repair shops vary depending on the location, make and model of the vehicle, and even the engine type. Most auto repair shops charge between $75 and $150 per hour.

What are Code Possible Symptoms?

  • Engine Light ON (or Service Engine Soon Warning Light)

What Does the B1155 Buick Code Mean?

When the ignition switch is turned to RUN position, Instrument Panel Cluster (IPC) sends two messages over the class 2 serial data line containing identification information. The first message contains serial data keying information, and the second message contains a partial Vehicle Identification Number (VIN). The Sensing and Diagnostic Module (SDM) compares these messages to the information stored in memory. The Diagnostic Trouble Code (DTC) B1155 sets when either message does not match information stored in SDM. DTC B1155 sets along with DTC B1159 or DTC B1160 depending on the message that does not match. If SDM does not receive the serial data keying message, DTC B1159 will be set without DTC B1155. If SDM does not receive a partial VIN message, DTC B1160 will be set without DTC B1155. Messages are sent only at POWER-ON.

B1155 Buick Code - SDM Calibration Mismatch

Need more Information on the Code?

Need more information on how to fix the B1155 Buick code? Get Access to Factory Service Manuals

Need Help with the Code?

Get the B1155 Buick code diagnosed by a professional: Find a repair shop in your area

Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service

  • Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
  • Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
  • Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
  • Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.
Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.