Engine-Codes.com
Engine-Codes – GMC – B1019 2015 GMC Sierra

B1019 2015 GMC Sierra Code - SDM System Configuration Error

Quick Answer

The B1019 diagnostic trouble code (DTC) for a 2015 GMC Sierra indicates a SDM (Sensing and Diagnostic Module) System Configuration Error. Common causes include Faulty wiring connections, Malfunctioning SDM module, Software glitches in the SDM system. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.

What it means
B1019 2015 GMC Sierra indicates SDM System Configuration Error.
Common causes
Common causes include Faulty wiring connections, Malfunctioning SDM module, Software glitches in the SDM system.
Severity
High - diagnose this code as soon as possible.
Can I drive?
Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
What is this?
Table of contents Created and updated by William Orellana on Sep 17, 2024
💬 Need more help? Ask Auto Expert for instant answers — it's free!
AutoCodes App

Fix Your Car Smarter

Try the New AutoCodes App!

Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.

AutoCodes App on Google Play

Code B1019 2015 GMC Sierra Description

The B1019 diagnostic trouble code (DTC) for a 2015 GMC Sierra indicates a SDM (Sensing and Diagnostic Module) System Configuration Error. The SDM is a crucial component of the vehicle's airbag system, responsible for deploying airbags in the event of a collision. When this error code is triggered, it means that there is a problem with the configuration of the SDM system, which could potentially compromise the proper functioning of the airbags in case of an accident.

OBDII Code B1019 2015 GMC Sierra - SDM System Configuration Error
B1019 2015 GMC Sierra Code - SDM System Configuration Error

Common Causes of B1019 2015 GMC Sierra

  1. Faulty wiring connections
  2. Malfunctioning SDM module
  3. Software glitches in the SDM system
  4. Issues with sensors communicating with the SDM
  5. Water damage or corrosion affecting the SDM system

Symptoms of B1019 2015 GMC Sierra

  1. Airbag warning light illuminated on the dashboard
  2. Inability to reset the airbag warning light
  3. Inconsistent or erratic airbag deployment
  4. Fault codes related to the SDM system in the vehicle's computer
  5. Loss of communication with the SDM module

How to Fix B1019 2015 GMC Sierra

  1. Diagnose the specific cause of the SDM System Configuration Error using a diagnostic scanner
  2. Inspect wiring connections for any damage or corrosion, repair or replace as necessary
  3. Check the SDM module for faults and replace if needed
  4. Update software in the SDM system to the latest version
  5. Test the airbag system to ensure proper functionality and reset the error codes

Cost to Fix B1019 2015 GMC Sierra

The cost of repairing a SDM System Configuration Error can vary depending on the specific cause of the issue. In general, the cost of parts for this repair can range from $200 to $600, with labor costs adding an additional $100 to $300. However, it's important to note that labor rates at auto repair shops can vary widely, typically ranging from $80 to $150 per hour. Rates may be higher at dealerships or in metropolitan areas, while independent shops may offer lower rates. It's advisable to check with local shops for a more accurate estimate based on your location and vehicle specifics.

What does this mean?

Tech Notes for B1019 2015 GMC Sierra

B1019:3A SDM System Configuration Error Incorrect Component Installed



Diagnostic Trouble Code (DTC) B1019 can be set after the Inflatable Restraint Sensing and Diagnostic Module (SDM) has been replaced and/or reprogrammed before the setup procedure is completed. The setup procedure cannot be completed if DTC B1019 is set as current or history. If a short or open is detected in a deployment circuit prior to the setup procedure being performed, the inflatable restraint sensing and diagnostic module will set DTC B1019.

Need more information about the B1019 2015 GMC Sierra code?

Need more information on how to fix the B1019 2015 GMC Sierra code? Get Access to Factory Service Manuals

Need Help with the Code?

Get the B1019 2015 GMC Sierra code diagnosed by a professional: Find a repair shop in your area

Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service

  • Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
  • Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
  • Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
  • Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.

Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.

About the author: William Orellana is a Master Mechanic and Mechanical Engineer with over 30 years of experience diagnosing and repairing vehicles. Learn more about his background.

Frequently Asked Questions about B1019 2015 GMC Sierra Code

1. What does the OBDII code B1019 mean on a 2015 GMC Sierra?

The code B1019 indicates a "SDM System Configuration Error," which typically points to a configuration mismatch or programming issue in the Supplemental Restraint System (SRS) module.

2. What are the common symptoms of the B1019 code on a 2015 GMC Sierra?

Symptoms may include the airbag warning light being illuminated, a chime or error message on the dashboard, and potential deactivation of the vehicle's airbag system.

3. What causes the B1019 code to appear on a 2015 GMC Sierra?

Common causes include incorrect programming of the SRS module, installation of an incompatible module, faulty wiring or connectors, or a module that has not been properly set up after replacement.

4. Is the airbag system affected when the B1019 code is active?

Yes, the airbag system may be disabled when this code is active, which could compromise occupant safety in the event of a collision.

5. How can I diagnose the B1019 code on my 2015 GMC Sierra?

Use an advanced scan tool to check for stored codes and verify the configuration of the SDM (Sensing and Diagnostic Module). Inspect related wiring and connectors for damage or corrosion.

6. Can the B1019 code be caused by a collision or airbag deployment?

Yes, the code can appear if the SDM was not properly reset or replaced after an airbag deployment or collision repair.

7. How do I fix the B1019 code on a 2015 GMC Sierra?

Repairs may involve reprogramming or recalibrating the SDM, ensuring the correct module is installed, or addressing wiring and connector issues if present.

8. Do I need a professional to fix the B1019 code?

Yes, resolving this issue often requires specialized diagnostic tools and expertise, so it's recommended to consult a certified technician or dealership.

9. Can I clear the B1019 code without fixing the issue?

Clearing the code without addressing the root cause will not solve the problem, and the code is likely to return. Additionally, the airbag system may remain inoperative.

10. What tools are needed to address the B1019 code on a 2015 GMC Sierra?

You’ll need an advanced scan tool capable of accessing the SRS module, along with software to reprogram or configure the SDM if necessary.

Discuss the causes and fixes for B1019 2015 GMC Sierra OBDII Code

Submit a New Comment

Code B1019 2015 GMC Sierra comments

No comments found for this page.