B0091 2018 GMC Sierra Code - Center Front Impact Sensor
Quick Answer
The B0091 diagnostic trouble code for a 2018 GMC Sierra refers to an issue with the center front impact sensor. Common causes include Wiring damage or corrosion, Faulty center front impact sensor, Issues with the airbag control module. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- B0091 2018 GMC Sierra indicates Center Front Impact Sensor.
- Common causes
- Common causes include Wiring damage or corrosion, Faulty center front impact sensor, Issues with the airbag control module.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
Code B0091 2018 GMC Sierra Description
The B0091 diagnostic trouble code for a 2018 GMC Sierra refers to an issue with the center front impact sensor. This sensor is a crucial component of the vehicle's safety system, as it is responsible for detecting impacts to the front of the vehicle and triggering the deployment of airbags in the event of a collision. When this sensor malfunctions or fails, it can compromise the effectiveness of the airbag system, putting occupants at risk in the event of an accident.
Common Causes of B0091 2018 GMC Sierra
- Wiring damage or corrosion
- Faulty center front impact sensor
- Issues with the airbag control module
- Impact or damage to the front bumper area
- Electrical system malfunction
Symptoms of B0091 2018 GMC Sierra
- Airbag warning light illuminated on the dashboard
- Airbags not deploying in a collision
- Inaccurate deployment of airbags
- Vehicle may fail safety inspections
- Loss of confidence in the vehicle's safety systems
How to Fix B0091 2018 GMC Sierra
- Begin by diagnosing the specific cause of the B0091 code using a diagnostic scanner to pinpoint the issue.
- Inspect the wiring harness connected to the center front impact sensor for any damage or corrosion. Repair or replace as necessary.
- Test the center front impact sensor itself to determine if it is faulty. Replace the sensor if needed.
- Check the airbag control module for any malfunctions or errors. Reset or replace the module if necessary.
- Clear the diagnostic trouble code from the vehicle's system and test the airbag system to ensure proper functionality.
Cost to Fix B0091 2018 GMC Sierra
The cost of repairing a B0091 code on a 2018 GMC Sierra can vary depending on the specific cause of the issue and the labor rates in your area. On average, you can expect to pay anywhere from $200 to $500 for parts and labor. Keep in mind that diagnostic time and labor rates can vary, so it's best to consult with a trusted mechanic or dealership for a more accurate estimate based on your location and vehicle specifics.
Tech Notes for B0091 2018 GMC Sierra
B0091:02 Center Front Impact Sensor Short to Ground
B0091:05 Center Front Impact Sensor Short to Battery or Open
B0091:0F Center Front Impact Sensor Erratic
B0091:39 Center Front Impact Sensor Internal Electronic Failure
B0091:3A Center Front Impact Sensor Incorrect Component Installed
B0091:71 Center Front Impact Sensor Invalid Serial Data Received
Need more information about the B0091 2018 GMC Sierra code?
Need more information on how to fix the B0091 2018 GMC Sierra code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the B0091 2018 GMC Sierra code diagnosed by a professional: Find a repair shop in your area
Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service
- Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
- Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
- Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
- Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.
Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.
Frequently Asked Questions about B0091 2018 GMC Sierra Code
1. What does OBDII code B0091 for a 2018 GMC Sierra mean?
The OBDII code B0091 for a 2018 GMC Sierra specifically refers to a fault with the Center Front Impact Sensor.
2. What are the common symptoms of a B0091 code in a 2018 GMC Sierra?
Common symptoms of a B0091 code in a 2018 GMC Sierra may include the airbag warning light illuminating on the dashboard and potential issues with the airbag system.
3. What are the possible causes of the B0091 code in a 2018 GMC Sierra?
Possible causes of a B0091 code in a 2018 GMC Sierra may include a faulty Center Front Impact Sensor, wiring issues, or a malfunction in the airbag control module.
4. How can I diagnose the B0091 code in my 2018 GMC Sierra?
Diagnosing a B0091 code in a 2018 GMC Sierra typically involves using a diagnostic scanner to retrieve the specific fault code, inspecting the wiring and connections to the Center Front Impact Sensor, and testing the sensor itself for proper functioning.
5. Can I continue driving my 2018 GMC Sierra with a B0091 code?
It is not recommended to drive a vehicle with a B0091 code, as it indicates a potential issue with the airbag system that could affect its functionality in the event of an accident.
6. How can I repair a B0091 code in my 2018 GMC Sierra?
Repairing a B0091 code in a 2018 GMC Sierra may involve replacing the faulty Center Front Impact Sensor, repairing any damaged wiring, or addressing any issues with the airbag control module.
7. Is it safe to reset a B0091 code in a 2018 GMC Sierra without fixing the underlying issue?
It is not safe to simply reset a B0091 code in a 2018 GMC Sierra without addressing the underlying problem, as it could compromise the effectiveness of the airbag system in case of an accident.
8. Are there any recalls related to the B0091 code for 2018 GMC Sierra models?
Recalls related to the B0091 code for 2018 GMC Sierra models should be checked with the manufacturer or a authorized dealership for any relevant information.
9. How much does it typically cost to repair a B0091 code in a 2018 GMC Sierra?
The cost of repairing a B0091 code in a 2018 GMC Sierra can vary depending on the specific cause of the issue, but it may involve parts and labor costs for sensor replacement or wiring repairs.
10. Can a DIY enthusiast fix a B0091 code in a 2018 GMC Sierra, or is it best left to professionals?
While some DIY enthusiasts may have the skills to diagnose and repair a B0091 code in a 2018 GMC Sierra, it is recommended to consult with a professional mechanic or technician for proper diagnosis and repair to ensure the safety and effectiveness of the airbag system.
Discuss the causes and fixes for B0091 2018 GMC Sierra OBDII Code
Code B0091 2018 GMC Sierra comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.