B0090 GMC Code - Rollover Sensor Erratic
Quick Answer
The B0090 GMC code indicates that there is an erratic signal coming from the rollover sensor in the vehicle. Common causes include Malfunctioning rollover sensor, Damaged wiring or connectors leading to the sensor, Faulty airbag control module. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- B0090 GMC indicates Rollover Sensor Erratic.
- Common causes
- Common causes include Malfunctioning rollover sensor, Damaged wiring or connectors leading to the sensor, Faulty airbag control module.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
Code B0090 GMC Description
The B0090 GMC code indicates that there is an erratic signal coming from the rollover sensor in the vehicle. The rollover sensor is a crucial component of the vehicle's safety system, as it is responsible for detecting when the vehicle is at risk of rolling over and deploying the appropriate safety measures, such as seatbelt pretensioners and side curtain airbags. When the rollover sensor is sending erratic signals, it can compromise the effectiveness of these safety features and put the occupants at risk in the event of a rollover accident.
Common Causes of B0090 GMC
- Malfunctioning rollover sensor.
- Damaged wiring or connectors leading to the sensor.
- Faulty airbag control module.
- Corrosion or water damage affecting the sensor.
- Impact or collision that has damaged the sensor or related components.
Symptoms of B0090 GMC
- Airbag warning light illuminated on the dashboard.
- Inconsistent deployment of safety features during a rollover simulation test.
- Vehicle may fail safety inspections due to malfunctioning safety systems.
- Increased risk of injury in the event of a rollover accident.
How to Fix B0090 GMC
- Begin by diagnosing the specific cause of the erratic signal from the rollover sensor using a diagnostic scanner.
- Inspect the wiring and connectors leading to the sensor for any damage or corrosion, repairing or replacing as needed.
- Test the rollover sensor itself to determine if it is functioning properly, replacing it if necessary.
- Check the airbag control module for any faults or errors, replacing it if needed.
- Clear the diagnostic trouble codes from the vehicle's system and perform a test to ensure that the rollover sensor is now sending accurate signals.
Cost to Fix B0090 GMC
The cost of repairing a B0090 GMC code can vary depending on the specific cause of the issue and the labor rates in your area. On average, you can expect to pay anywhere from $200 to $500 for parts and labor to address this problem. Keep in mind that additional costs may be incurred if other components need to be replaced or if further diagnostics are required. It's recommended to consult with a qualified mechanic to get an accurate estimate for your particular vehicle. Labor rates at auto repair shops typically range from $80 to $150 per hour, but can vary based on location and shop rates.
Tech Notes for B0090 GMC
DTC B0090 0F Rollover Sensor Erratic
DTC B0090 3A Rollover Sensor Incorrect Component Installed
DTC B0090 39 Rollover Sensor Internal Electronic Failure
DTC B0090 71 Rollover Sensor Invalid Serial Data Received
Need more information about the B0090 GMC code?
Need more information on how to fix the B0090 GMC code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the B0090 GMC code diagnosed by a professional: Find a repair shop in your area
Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service
- Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
- Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
- Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
- Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.
Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.
Frequently Asked Questions about B0090 GMC Code
1. What are the common symptoms of OBDII code B0090 GMC (Rollover Sensor Erratic)?
- The common symptoms include the airbag warning light being illuminated on the dashboard and a potential loss of communication with the rollover sensor.
2. What could cause the OBDII code B0090 GMC to trigger?
- The code B0090 GMC is typically triggered by a faulty rollover sensor, wiring issues, or a malfunction in the airbag system.
3. How can I diagnose the cause of the OBDII code B0090 GMC?
- Diagnosing the issue involves using a scan tool to retrieve the specific fault code, checking the wiring connections to the rollover sensor, and performing a visual inspection for any signs of damage.
4. Can I continue driving my vehicle with the OBDII code B0090 GMC active?
- It is not recommended to drive the vehicle with an active B0090 code, as it indicates a potential issue with the airbag system that could compromise safety in the event of a rollover.
5. What are some repair tips for fixing the OBDII code B0090 GMC?
- Repair tips include checking and repairing any damaged wiring, resetting the fault codes after fixing the issue, and ensuring proper connection of the rollover sensor.
6. Is it possible to reset the OBDII code B0090 GMC without fixing the underlying issue?
- While you can clear the fault code temporarily, it will likely reappear until the root cause, such as a faulty rollover sensor, is addressed.
7. How much does it typically cost to repair the OBDII code B0090 GMC?
- The cost of repair can vary depending on the specific cause of the issue, but it may involve replacing the rollover sensor, repairing wiring, or addressing other related components.
8. Can I fix the OBDII code B0090 GMC myself, or do I need to take it to a mechanic?
- If you have experience with automotive repair and diagnostics, you may be able to address the issue yourself. However, if you are unsure or uncomfortable working on airbag systems, it is best to consult a professional mechanic.
9. Are there any safety concerns associated with the OBDII code B0090 GMC?
- Yes, there are safety concerns as the code relates to the proper functioning of the airbag system, which is crucial for occupant protection in the event of a rollover.
10. How urgent is it to address the OBDII code B0090 GMC once it appears?
- It is important to address the B0090 code promptly to ensure the proper functioning of the airbag system and maintain vehicle safety standards.
Discuss the causes and fixes for B0090 GMC OBDII Code
Code B0090 GMC comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.