B008F:02 Code - Rollover Protection Disable Switch Circuit Short to Ground
Quick Answer
The B008F:02 diagnostic trouble code (DTC) indicates a problem with the Rollover Protection Disable Switch Circuit shorting to ground in the vehicle. Common causes include Damaged wiring or connectors in the disable switch circuit, Faulty rollover protection disable switch, Corrosion or moisture intrusion in the circuit. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- B008F:02 indicates Rollover Protection Disable Switch Circuit Short to Ground.
- Common causes
- Common causes include Damaged wiring or connectors in the disable switch circuit, Faulty rollover protection disable switch, Corrosion or moisture intrusion in the circuit.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
Code B008F:02 Description
The B008F:02 diagnostic trouble code (DTC) indicates a problem with the Rollover Protection Disable Switch Circuit shorting to ground in the vehicle. This switch is a safety feature designed to disable the rollover protection system, which typically includes features like roll bars or pop-up roll hoops, in case of an emergency or maintenance situation. When this circuit is shorted to ground, it means that there is an unintended connection between the switch and the vehicle's ground, which can prevent the system from functioning properly.
Common Causes of B008F:02
- Damaged wiring or connectors in the disable switch circuit.
- Faulty rollover protection disable switch.
- Corrosion or moisture intrusion in the circuit.
- Short circuit caused by a damaged component in the system.
- Issues with the control module or related electronics.
Symptoms of B008F:02
- Airbag warning light illuminated on the dashboard.
- Rollover protection system not activating during system test.
- Fault code stored in the vehicle's onboard diagnostic system.
- Loss of functionality in the rollover protection system.
How to Fix B008F:02
- Begin by conducting a visual inspection of the disable switch circuit wiring and connectors for any signs of damage or corrosion.
- Test the rollover protection disable switch for proper functionality using a multimeter or scan tool.
- Check for any short circuits in the circuit by performing continuity tests on the wiring and components.
- Inspect the control module for any signs of damage or malfunction, and replace if necessary.
- Clear the fault code from the vehicle's onboard diagnostic system and perform a system test to ensure proper operation of the rollover protection system.
Cost to Fix B008F:02
The cost of repairing a Rollover Protection Disable Switch Circuit Short to Ground issue can vary depending on the extent of the damage and the specific components that need to be replaced. In general, you can expect to pay anywhere from $150 to $500 for parts and labor for this repair. Keep in mind that labor rates at auto repair shops can vary, so it's advisable to check with local shops for more accurate pricing information. Additionally, the cost may be higher if the control module or other expensive components need to be replaced.
Tech Notes for B008F:02
B008F:05 Rollover Protection Disable Switch Circuit High Voltage/Open
Need more information about the B008F:02 code?
Need more information on how to fix the B008F:02 code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the B008F:02 code diagnosed by a professional: Find a repair shop in your area
Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service
- Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
- Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
- Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
- Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.
Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.
Frequently Asked Questions about B008F:02 Code
1. What are common symptoms of OBDII code B008F:02 - Rollover Protection Disable Switch Circuit Short to Ground?
The common symptoms may include the airbag warning light illuminating on the dashboard and a message indicating an issue with the rollover protection system.
2. What can cause the Rollover Protection Disable Switch Circuit to short to ground?
A short to ground in the Rollover Protection Disable Switch Circuit can be caused by damaged wiring, a faulty rollover protection disable switch, or a problem with the control module.
3. How serious is the B008F:02 code related to the Rollover Protection Disable Switch Circuit Short to Ground?
This code is considered serious as it indicates a potential safety issue with the rollover protection system, which is designed to deploy airbags in the event of a rollover accident.
4. How can I diagnose the cause of OBDII code B008F:02?
Diagnosing this code typically involves using a scan tool to retrieve the specific fault code, checking the wiring and connections in the rollover protection system, and testing the rollover protection disable switch.
5. Can I still drive my vehicle with the B008F:02 fault code?
It is not recommended to drive the vehicle with this fault code present, as it indicates a potential safety issue with the rollover protection system that may affect its functionality in the event of an accident.
6. Is it possible to repair the Rollover Protection Disable Switch Circuit Short to Ground issue myself?
Repairing this issue may require advanced knowledge and diagnostic tools. It is recommended to consult a professional mechanic or dealership to properly diagnose and repair the problem.
7. How much does it typically cost to repair the Rollover Protection Disable Switch Circuit Short to Ground issue?
The cost of repairing this issue can vary depending on the underlying cause. It may involve replacing damaged wiring, the rollover protection disable switch, or the control module, which can range from a few hundred to a thousand dollars.
8. Can resetting the OBDII code B008F:02 make the problem go away temporarily?
Resetting the code may temporarily turn off the warning light, but it will not fix the underlying issue causing the fault code. It is important to diagnose and repair the problem to ensure the safety systems are functioning correctly.
9. Are there any safety risks associated with driving with the Rollover Protection Disable Switch Circuit Short to Ground fault code?
Driving with this fault code present may pose a safety risk, as the rollover protection system may not deploy airbags properly in the event of a rollover accident. It is best to address the issue promptly.
10. How long does it typically take to repair the Rollover Protection Disable Switch Circuit Short to Ground issue?
The repair time can vary depending on the exact cause of the fault. Simple fixes like repairing wiring may take a few hours, while more complex issues involving component replacement could take longer.
Discuss the causes and fixes for B008F:02 OBDII Code
Code B008F:02 comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.