Engine-Codes - Ford - B007F Ford

B007F Ford Code - Passenger Seatbelt Pretensioner 'C' Deployment Control

- Code Popularity: 9,882 Views
- Repair Importance Level: 3/3
- Repair Difficulty Level: 3/3
Table of contents

What are the Possible Causes of the Code B007F Ford?

  • Faulty Passenger Seatbelt Pretensioner
  • Passenger Seatbelt Pretensioner harness is open or shorted
  • Passenger Seatbelt Pretensioner circuit poor electrical connection
  • Faulty Restraints Control Module (RCM)

How to Fix the B007F Ford Code?

Start by checking the "Possible Causes" listed above. Visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector's pins.

Code B007F Ford Tech Notes

B007F:11 Passenger Seatbelt Pretensioner 'C' Deployment Control: Circuit Short to Ground
B007F:12 Passenger Seatbelt Pretensioner 'C' Deployment Control: Circuit Short to Battery
B007F:13 Passenger Seatbelt Pretensioner 'C' Deployment Control: Circuit Open
B007F:1A Passenger Seatbelt Pretensioner 'C' Deployment Control: Circuit Resistance Below Threshold

What is the Cost to Diagnose the Code B007F Ford?

Labor: 1.0

The cost to diagnose the B007F Ford code is 1.0 hour of labor. The auto repair's diagnosis time and labor rates vary by location, vehicle's make and model, and even your engine type. Most auto repair shops charge between $75 and $150 per hour.

Does your Ford have Safety Recalls? → Check here

What are Code B007F Ford Possible Symptoms?

  • Air Bag Warning Light ON

What Does the B007F Ford Code Mean?

The Restraints Control Module (RCM) analyzes the deployment loop resistance to determine if a fault exists. The value displayed in the PID is the deployment loop resistance measured by the RCM. If the value displayed is lower or higher than the desired range, the RCM can set a Diagnostic Trouble Code (DTC). As the deployment loop resistance drifts farther outside the desired range, the chance for a DTC increases. Small variations in resistance can occur due to the effect of road vibrations on terminal fit. Crimps and terminals can be affected by stress and harness movement and can cause an increase in resistance due to wire strain. These variables can result in an intermittent fault. For this reason, the test requires the PID value to be within the desired range before the fault is considered repaired, regardless if the module is reporting an on-demand DTC at the time of diagnosis. Following this direction helps make sure that minor changes in resistance do not create a repeat concern. This test uses the process of elimination to diagnose each part of the deployment loop circuit including:
- Wiring
- Connections
- Driver seatbelt anchor pretensioner

B007F Ford Code - Passenger Seatbelt Pretensioner 'C' Deployment Control

Need more Information on the B007F Ford Code?

Need more information on how to fix the B007F Ford code? Get Access to Factory Service Manuals

Need Help with the B007F Ford Code?

Get the B007F Ford code diagnosed by a professional: Find a repair shop in your area

Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service

  • Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
  • Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
  • Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
  • Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.
Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.