Engine-Codes - Pontiac - B0071 Pontiac

B0071 Pontiac Code - Passenger Seat Belt Tension Sensor Circuit

- Code Popularity: 1,923 Views
- Repair Importance Level: 3/3
- Repair Difficulty Level: 3/3
Table of contents
ChatAC AutoCodes.com AI Chat

What are the Possible Causes of the DTC B0071 Pontiac?

NOTE: The causes shown may not be a complete list of all potential problems, and it is possible that there may be other causes.
  • Faulty Passenger Seat Belt Retractor (Passenger Seat Belt Tension Sensor)
  • Passenger Seat Belt Retractor harness is open or shorted
  • Passenger Seat Belt Retractor circuit poor electrical connection
  • Faulty Passenger Presence Module

Code Tech Notes

B0071:03 Passenger Seat Belt Tension Sensor Circuit Voltage Below Threshold
B0071:04 Passenger Seat Belt Tension Sensor Circuit Open
B0071:07 Passenger Seat Belt Tension Sensor Circuit Voltage Above Threshold
B0071:08 Passenger Seat Belt Tension Sensor Circuit Voltage Performance Signal Invalid

⚠ Does your Pontiac have Safety Recalls? → Check here

How to Fix the DTC B0071 Pontiac?

Check the 'Possible Causes' listed above. Visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector pins.

Search for B0071 Pontiac Questions and Answers: Search here →

What is the Cost to Diagnose the Code?

Labor: 1.0

The cost to diagnose the B0071 Pontiac code is 1.0 hour of labor. The diagnosis time and labor rates at auto repair shops vary depending on the location, make and model of the vehicle, and even the engine type. Most auto repair shops charge between $75 and $150 per hour.

What are Code Possible Symptoms?

  • Air Bag Warning Light ON

What Does the B0071 Pontiac Code Mean?

The seat belt tension sensor is a sensor mounted on the passenger seat belt retractor and provides input to the Passenger Presence Module. When an infant car seat is properly restrained on the front passenger seat, the seat belt is tightly secured through the car seat. The seat belt pulls on the tension sensor and changes the voltage signal to the Passenger Presence Module. The Passenger Presence Module monitors the belt tension sensor signal circuit and if a fault is detected, the Diagnostic Trouble Code (DTC) will be set. When the Passenger Presence Module detects this DTC, it will send out a serial data message, and the Inflatable Restraint Sensing and Diagnostic Module will notify the customer of the enable/disable status by illuminating the OFF indicator on the PASSENGER AIR BAG ON/OFF indicators. The Inflatable Restraint Sensing and Diagnostic Module (SDM) will then suppress the deployment of the passenger instrument panel air bag and illuminate the AIR BAG indicator.

B0071 Pontiac Code - Passenger Seat Belt Tension Sensor Circuit

Need more Information on the Code?

Need more information on how to fix the B0071 Pontiac code? Get Access to Factory Service Manuals

Need Help with the Code?

Get the B0071 Pontiac code diagnosed by a professional: Find a repair shop in your area

Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service

  • Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
  • Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
  • Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
  • Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.
Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.