B0052 2017 GMC Sierra Code - Deployment Commanded
Quick Answer
The B0052 diagnostic trouble code (DTC) for a 2017 GMC Sierra indicates that the airbag deployment system has been commanded to deploy. Common causes include Faulty crash sensor triggering the airbag deployment command, Wiring issues such as shorts or open circuits in the airbag system, Malfunctioning airbag control module. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- B0052 2017 GMC Sierra indicates Deployment Commanded.
- Common causes
- Common causes include Faulty crash sensor triggering the airbag deployment command, Wiring issues such as shorts or open circuits in the airbag system, Malfunctioning airbag control module.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
Code B0052 2017 GMC Sierra Description
The B0052 diagnostic trouble code (DTC) for a 2017 GMC Sierra indicates that the airbag deployment system has been commanded to deploy. This code typically triggers when the vehicle's airbag control module detects a fault or malfunction in the system that requires the deployment of the airbags. This could be due to a variety of reasons, such as a crash sensor being triggered, a wiring issue, or a faulty airbag control module.
Common Causes of B0052 2017 GMC Sierra
- Faulty crash sensor triggering the airbag deployment command.
- Wiring issues such as shorts or open circuits in the airbag system.
- Malfunctioning airbag control module.
- Corrosion or damage to the connectors in the airbag system.
- Impact or collision that caused the airbag deployment command to be triggered.
Symptoms of B0052 2017 GMC Sierra
- Airbag warning light illuminated on the dashboard.
- Inability to turn off the airbag warning light.
- Diagnostic trouble code B0052 stored in the vehicle's computer system.
- Loss of communication with the airbag control module.
- In some cases, the airbags may deploy unexpectedly.
How to Fix B0052 2017 GMC Sierra
- Begin by diagnosing the specific cause of the B0052 code by using a scan tool to retrieve freeze frame data and any other related codes.
- Inspect the crash sensors, wiring, and connectors in the airbag system for any signs of damage or corrosion.
- Test the airbag control module to determine if it is functioning correctly or needs to be replaced.
- Clear the DTC from the vehicle's computer system after addressing the root cause of the issue.
- Perform a thorough test drive to ensure that the airbag warning light does not reappear and that the airbag system is functioning properly.
Cost to Fix B0052 2017 GMC Sierra
The typical repair costs for addressing a B0052 code in a 2017 GMC Sierra can vary depending on the specific cause of the issue. In general, the cost of parts such as a new airbag control module or crash sensor can range from $200 to $600. Labor costs at an auto repair shop can add an additional $100 to $300 to the total repair bill. It is important to note that diagnosis time and labor rates can vary based on location, vehicle make and model, and the shop's hourly rates. It is advisable to check with local auto repair shops for a more accurate estimate.
Need more information about the B0052 2017 GMC Sierra code?
Need more information on how to fix the B0052 2017 GMC Sierra code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the B0052 2017 GMC Sierra code diagnosed by a professional: Find a repair shop in your area
Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service
- Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
- Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
- Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
- Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.
Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.
Frequently Asked Questions about B0052 2017 GMC Sierra Code
1. What does OBDII code B0052 for a 2017 GMC Sierra mean?
The B0052 code indicates that the Deployment Commanded signal from the sensing and diagnostic module (SDM) has been detected as being stuck on.
2. What are the common symptoms of OBDII code B0052 in a 2017 GMC Sierra?
Common symptoms of code B0052 may include the airbag warning light being illuminated on the dashboard and potential issues with the airbag system.
3. What are possible causes of OBDII code B0052 in a 2017 GMC Sierra?
Possible causes of code B0052 can include a faulty SDM, wiring issues, a malfunctioning clock spring, or problems with the airbag system itself.
4. How can I diagnose OBDII code B0052 in my 2017 GMC Sierra?
Diagnosing code B0052 typically involves using a professional OBDII scanner to retrieve the code, inspecting the wiring and connections related to the airbag system, and performing tests on the SDM and other components.
5. Is it safe to drive my 2017 GMC Sierra with OBDII code B0052?
It is not recommended to drive the vehicle with an active airbag system fault code like B0052, as it may compromise the functionality of the airbags in the event of a collision.
6. Can I reset OBDII code B0052 in my 2017 GMC Sierra by disconnecting the battery?
While disconnecting the battery may clear the code temporarily, it is important to diagnose and repair the underlying issue causing code B0052 to prevent it from recurring.
7. How much does it typically cost to repair OBDII code B0052 in a 2017 GMC Sierra?
The cost of repairing code B0052 can vary depending on the specific cause of the issue, but it may involve replacing components like the SDM, clock spring, or repairing wiring, potentially ranging from a few hundred to over a thousand dollars.
8. Can I fix OBDII code B0052 in my 2017 GMC Sierra myself?
Repairing code B0052 may require specialized tools and knowledge of airbag systems, so it is recommended to consult a professional mechanic or dealership to properly diagnose and repair the issue.
9. Will OBDII code B0052 cause my 2017 GMC Sierra to fail a car inspection?
Since code B0052 relates to the airbag system, it is possible that it may cause your vehicle to fail a safety inspection, depending on local regulations and the severity of the issue.
10. How long does it typically take to repair OBDII code B0052 in a 2017 GMC Sierra?
The repair time for code B0052 can vary based on the cause of the issue and the availability of parts, but it may take a few hours to a full day to diagnose and fix the problem.
Discuss the causes and fixes for B0052 2017 GMC Sierra OBDII Code
Code B0052 2017 GMC Sierra comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.