B001E:02 Code - Driver Seat Inboard Side Air Bag Deployment Loop Short to Ground
Quick Answer
The B001E:02 diagnostic trouble code (DTC) indicates that there is a short to ground in the driver seat inboard side airbag deployment loop. Common causes include Damaged wiring or connectors in the driver seat inboard side airbag deployment loop, Faulty airbag module, Corrosion or poor connections in the airbag sensor system. Severity is High - diagnose this code as soon as possible. Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
- What it means
- B001E:02 indicates Driver Seat Inboard Side Air Bag Deployment Loop Short to Ground.
- Common causes
- Common causes include Damaged wiring or connectors in the driver seat inboard side airbag deployment loop, Faulty airbag module, Corrosion or poor connections in the airbag sensor system.
- Severity
- High - diagnose this code as soon as possible.
- Can I drive?
- Driving is not recommended if the warning light is flashing, the engine runs poorly, or safety-related symptoms are present.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.
Code B001E:02 Description
The B001E:02 diagnostic trouble code (DTC) indicates that there is a short to ground in the driver seat inboard side airbag deployment loop. This loop is a crucial part of the vehicle's safety system, designed to deploy the airbag in the event of a collision to protect the driver from injury. When a short to ground occurs in this loop, it means that there is an unintended connection between the electrical circuit and the vehicle's chassis or ground. This can prevent the airbag from deploying properly in an accident, compromising the safety of the driver.
Common Causes of B001E:02
- Damaged wiring or connectors in the driver seat inboard side airbag deployment loop
- Faulty airbag module
- Corrosion or poor connections in the airbag sensor system
- Impact or collision that damages the airbag system components
- Electrical issues such as a short circuit in the system
Symptoms of B001E:02
- Illumination of the airbag warning light on the dashboard
- Inability to activate the driver seat inboard side airbag
- Diagnostic trouble code B001E:02 stored in the vehicle's computer system
- Intermittent or non-functioning horn or cruise control buttons on the steering wheel
How to Fix B001E:02
- Begin by disconnecting the vehicle's battery to prevent accidental airbag deployment.
- Inspect the wiring and connectors in the driver seat inboard side airbag deployment loop for any damage or corrosion.
- Test the airbag module and sensor system for proper functionality.
- Repair or replace any damaged wiring, connectors, or components as needed.
- Clear the diagnostic trouble code from the vehicle's computer system and perform a thorough system check to ensure proper airbag deployment.
Cost to Fix B001E:02
The typical repair costs for addressing a driver seat inboard side airbag deployment loop short to ground issue can vary depending on the extent of the damage and the specific components that need to be repaired or replaced. In general, the cost of parts for this repair can range from $200 to $500, while labor costs can range from $150 to $300. However, it's important to note that these are rough estimates, and actual costs may vary based on factors such as the vehicle make and model, the location of the repair shop, and the expertise of the technician. It's recommended to consult with a qualified mechanic or repair shop for a more accurate cost estimate based on your specific situation.
Tech Notes for B001E:02
B001E:02 Driver Seat Inboard Side Air Bag Deployment Loop Short to Ground
B001E:04 Driver Seat Inboard Side Air Bag Deployment Loop Open
B001E:0D Driver Seat Inboard Side Air Bag Deployment Loop High Resistance
B001E:0E Driver Seat Inboard Side Air Bag Deployment Loop Low Resistance
Need more information about the B001E:02 code?
Need more information on how to fix the B001E:02 code? Get Access to Factory Service Manuals
Need Help with the Code?
Get the B001E:02 code diagnosed by a professional: Find a repair shop in your area
Precautions for SRS “AIR BAG” and “SEAT BELT PRE-TENSIONER” Service
- Never probe the electrical connectors on air bag, side air curtain modules or seat belts.
- Never disassemble or tamper with safety belt buckle/retractor pretensioners, adaptive load limiting retractors, safety belt inflators, or probe the electrical connectors.
- Do not use electrical test equipment to check SRS circuits unless instructed to in this Service Manual.
- Before servicing the SRS, turn ignition switch OFF, disconnect both battery cables and wait at least 3 minutes. For approximately 3 minutes after the cables are removed, it is still possible for the air bag and seat belt pre-tensioner to deploy. Therefore, do not work on any SRS connectors or wires until at least 3 minutes have passed.
Failure to follow this instruction may result in the accidental deployment of these modules, which increases the risk of serious personal injury or death.
Frequently Asked Questions about B001E:02 Code
What does the OBDII code B001E:02 mean?
1. The code B001E:02 indicates a short to ground in the driver seat inboard side airbag deployment loop circuit, which may compromise airbag functionality. 2.
What are the common symptoms of the B001E:02 code?
Symptoms may include an illuminated airbag warning light, the driver-side airbag not deploying in an accident, and potentially other safety system malfunctions. 3.
What causes the B001E:02 code?
Common causes include damaged or frayed wiring, a faulty airbag module, a defective clock spring, or a damaged connector in the airbag system. 4.
Is it safe to drive with the B001E:02 code active?
No, it is not safe to drive with this code active as it indicates a potential malfunction in the airbag system, which may fail to deploy in an accident. 5.
How can I diagnose the B001E:02 code?
Diagnose the code by inspecting the wiring and connectors for the driver seat inboard side airbag, checking for shorts to ground, and using a scan tool to verify fault codes. 6.
Can I reset the airbag light to fix the B001E:02 code?
No, simply resetting the airbag light will not fix the issue. The underlying short to ground in the airbag circuit must be repaired first. 7.
How much does it cost to repair the B001E:02 code?
Repair costs vary depending on the issue, but common repairs like wiring fixes or connector replacements typically range from $100 to $300. Replacing a module or clock spring may cost more. 8.
Can a faulty clock spring cause the B001E:02 code?
Yes, a faulty clock spring can cause this code if it disrupts the electrical connection to the airbag deployment loop. 9.
What tools are needed to fix the B001E:02 code?
You may need a multimeter to check for shorts, a scan tool for diagnostics, and basic hand tools to inspect and repair the wiring or connectors. 10.
Who should repair the B001E:02 code?
Since the airbag system is a critical safety component, repairs should be performed by a qualified mechanic or automotive technician familiar with airbag systems.
Discuss the causes and fixes for B001E:02 OBDII Code
Code B001E:02 comments
No comments found for this page.
Fix Your Car Smarter
Try the New AutoCodes App!
Get complete OBDII diagnostics, repair solutions, and cost estimates, plus AI chat support on demand.